■ Lowdown spring
Gives a sense of dynamism to the styling and stabilizes handling by lowering the center of gravity.The dedicated design according to the power unit ensures an appropriate amount of down and suspension stroke.The spring constant is set in consideration of the damping ratio with the damper.It is recommended to use an adjustable stabilizer link that corrects the stabilizer arm angle during lowdown.　>> More details

<Main specifications> ・ Vehicle height: -20mm ・ Spring constant isCLICK HEREPlease refer to

■ Sports damper
Although it has the same shape as the mass-produced product, the internal piston adopts a "very low speed valve" that generates precise damping force from the moment it starts moving.It accurately controls changes in the vehicle's posture and achieves a sporty, flat and high-quality ride.It is recommended to use with genuine springs (can be used with lowdown springs).>> More details

<Main specifications> ・ Fixed gas damping force

■ Adjustable stabilizer link
Adjustable link that corrects the deviation of the stabilizer arm angle that occurs when the vehicle height is lowered, such as installing a low down spring.The total length of the link connecting the stabilizer and the car body is adjusted to optimize the arm angle, and the original stabilizer function of the design value is restored.Set for front / rear.>> More details

<Main specifications> ・ Front / rear settings ・ Full length adjustable XNUMX-piece set ・ Axial mount type

■ Sports stabilizer
The left and right suspension arms are connected by a pipe, and the spring effect suppresses the amount of roll.Controllability during cornering is maintained by increasing the spring constant appropriately.It is especially effective when increasing the size of tires to high grip tires.Set for front / rear. >> More details

<Main specifications> ・ Front / rear settings ・ Front: solid Φ22 ・ Rear: solid Φ18 ~ 20

■ Strut tower bar
The first step to reinforce the body connecting the left and right strut towers.The steel oval shaft and one-piece structure, which are advantageous in terms of rigidity, ensure the highest level of strength for a general tower bar.It is effective when installed separately, but it is best used in combination with a floor crossbar. >> More details

<Main specifications> -Steel 2-piece structure XNUMX-point type

■ Center floor bar
It suppresses distortion near the center of the body monocoque, which cannot be compensated by strut tower bars and floor crossbars, and compensates for the "annular structure" effect of the SKYACTIV body.I try to have a low center of gravity layout that does not sacrifice the leg space of the rear seats as much as possible. >> More details

<Main specifications> -Steel oval shaft 1-piece configuration 4-point type

■ Floor crossbar
With a simple structure that allows one bar to crawl in the left-right direction of the floor, it demonstrates the tower bar effect.Since it also serves as a suspension mounting point with high strength, the burden on the body is extremely small.There is almost no impact on the utility space.It is effective when used alone, but it is recommended to install it together with the strut tower bar. >> More details

<Main specifications> -Steel oval shaft 2-piece structure 4-point type

■Lower arm bar (front)
By connecting the bases of the left and right lower arms, which are the suspension mounting base points, with steel oval pipes, minute alignment changes are suppressed.Improves the feeling of handling. >> More details

<Main specifications> -Steel oval shaft 1-piece structure 2-point type

■Lower arm bar (rear)
By connecting the bases of the left and right lower arms, which are the suspension mounting base points, with steel oval pipes, minute alignment changes are suppressed.Improves the feeling of handling. >> More details

<Main specifications> -Steel oval shaft 1-piece structure 2-point type

■ Motion control beam
Reinforces the front and rear ends of the body to increase torsional rigidity.By suppressing the vibration of the body due to high rigidity with an ultra-high damping friction type damper, it creates a street-best ride with strength and suppleness.A set of two front and back.>> More details

<Main specifications> ・ Friction type damper + steel shaft ・ With special mounting bracket

■ Air filter replacement
Utilizing the air cleaner case of mass-produced cars, replacing only the filter part effectively improves the accelerator response.The dry filter, which has a good balance between ventilation performance and dust collection effect, is a disposable type that has little effect on the air flow sensor and is easy to maintain.　>> More details

<Main specifications> ・ Dry type ・ Disposable (disposable) type

■ Sports induction box
By utilizing the air cleaner box of a mass-produced vehicle, the intake side case is replaced. Fresh air is directly guided to the air filter, improving intake efficiency. The sound also becomes sporty. Combining it with the optional air filter replacement increases efficiency even further.　>> More details

<Main specifications> -Funnel type FRP frame + aluminum heat shield

■ Fresh air guide
The "Fresh Air Guide" is an item that supports the improvement of intake efficiency by directly capturing the running wind from the front of the vehicle body.By directly connecting the front grille, which does not have a clear intake path in mass-produced vehicles, to the air intake port installed at the top of the core support with a dedicated air duct, the effect of exhaust heat from radiators etc. is minimized, and fresh air is air cleanered. It is introduced in the box to improve the filling efficiency. >> More details

<Main specifications> -FRP red gel coat finish

■ Intake suction kit
Specifications that secure the maximum effective flow path area of ​​intake air and reduce intake resistance.The material used is multi-layer polystar silicon or FRP pipe, which has a high effect of suppressing deformation due to suction negative pressure.As a result, the accelerator response has been improved.The crimson coloring adds an accent to the engine room.　>> More details

<Main specifications> -Made of FRP / 4-layer polystar silicon hose-Detailed specificationsCLICK HERE for more information.

■ Street sports brake pads
The aim is "deceleration at will".Designed with an emphasis on stable effectiveness during continuous braking, delicate load transfer in cornering, and flexible control of vehicle speed, rather than simply stopping performance.Focus on the amount of change and how to change the coefficient of friction (μ), which constantly changes depending on various conditions such as pedaling force, speed, and temperature.The "transient characteristics of μ" required by sports-oriented drivers realizes a taste that is synchronized with the sensibilities.　>> More details

<Main specifications> ・ Non-asbestos friction material ・ Rotor proper temperature: 0 to 400 ℃

■ Street brake rotor
Mass-produced XNUMX-piece structure with the same shape FC Cast iron, but with improved strength by controlling the content of carbon and silicon.Further heat treatment is applied to stabilize the metal connective tissue.It suppresses distortion due to heat and improves fade resistance and crack resistance. >> More details

<Main specifications> ・ 6 slits on one side, 1 piece type

■Brake pedal brace
The bracket of the pedal mounting part, which causes slight distortion during brake operation, is three-dimensionally reinforced with steel braces to ensure rigidity.It improves the delay in reaction from when the pedal is pressed until the brake is applied, and contributes to a direct effect.>> More details

<Main specifications> -Steel 2-piece structure

■Sports radiator cap
By increasing the opening pressure of the pressure regulating valve to 127kpa (1.3kg/cm²), the boiling point of the coolant is raised. This keeps the pressure in the cooling system high and suppresses the boiling and evaporation of the coolant. This provides a stable cooling effect even during sporty driving. The seal uses a silicone packing that boasts high heat resistance and durability. This maintains a tight seal over the long term, preventing coolant leaks and pressure drops. >> More details

<Main specifications> ・Operating valve pressure 127kpa (1.3kg/cm²) ・Sealing part heat-resistant silicone rubber

■ Sports oil filter
Fine sludge is removed by using a high-efficiency filter medium.By expanding the filtration area by about 5% compared to mass production, filtration efficiency is improved and pressure loss is reduced.Furthermore, by incorporating a powerful neodymium magnet, metal wear debris is captured without missing.It balances the functions required for oil filters at a high level.Dedicated to gasoline engine vehicles. >> More details

<Main specifications> ・ Built-in strong magnet ・ Filtration area expanded by about 5% compared to mass production

■Sports ignition coil
By increasing the efficiency of current flow from the battery to the primary coil, the magnetic energy inside the coil is amplified. This increases the secondary voltage from the coil, resulting in a stable, uniform, and powerful spark discharge from the spark plug. By ensuring the air-fuel mixture in the engine combustion chamber is burned, the accelerator response is sharpened and the output characteristics are stabilized. >> More details

<Main specifications> High-efficiency mass-produced identical shape AutoExe red housing Number of units: 4

■ Sports clutch line
Uses stainless mesh PTFE (Teflon), which has less deterioration due to heat and aging and less expansion due to hydraulic pressure than the rubber used in mass-produced vehicles.Contributes to a direct clutch feel.In addition, PVC coating is applied to protect the hose for safety. >> More details

<Main specifications> -Stainless steel mesh PTFE + PVC coating

■ Turbo pipe
By optimizing the layout of the turbo pipe that guides the air supercharged by the turbine to the intercooler, and combining the aluminum elbow pipe whose inner wall is mirrored as much as possible and the 4-layer polyster silicon that has a high deformation suppressing effect, the hose expands due to pressurization. And suppresses the resistance of the air flow path.As a result, the boost pressure rises faster and turbo lag is reduced.Improve the response from the beginning of stepping on the accelerator.The product comes with a gasket required for installation. >> More details

<Main specifications> -Aluminum pipe (anodized) + silicon hose / band / gasket included

■ Oil filler cap
The oil filler cap has been changed from genuine resin to 52S aluminum, which is fully machined and full of craftsmanship.Brilliant red alumite processing is applied to give a mechanical and gorgeous accent to the engine room.The laser-engraved AutoExe logo is also a delicate impression.　>> More details

<Main specifications> ・ 52S aluminum fully machined ・ Red alumite processing ・ Laser engraved with AutoExe logo

■ Brake fluid cap
The resin mass-produced brake fluid tank cap has been upgraded to aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.Combined with an oil filler cap and level gauge grip with the same design, it accelerates the total coordination of the engine room.　>> More details

<Main specifications> -Aluminum-Fully machined-Red alumite processing-Laser engraved AutoExe logo included

■ Fuel cap cover
An ABS cover that can be attached over a mass-produced fuel cap.The design with cap bolts on bright Exe Red gives a gorgeous impression to the fuel filler port. With AutoExe logo.Compatible with a wide range of current Mazda vehicles.　>> More details

<Main specifications> ・ ABS red painted ・ With decorative cap bolt ・ With AutoExe logo ・ Double-sided tape attached ・ Fuel label / erroneous oil supply prevention reminder sticker included

■ Optima Battery
Synonymous with maintenance-free batteries, which boast a longer life than conventional open-type batteries.It is a completely sealed type that uses the original spiral cell technology, so there is no need to replenish the battery fluid.Provides a stable current even under high load.Can be installed without using additional adapters.>> More details

<Main specifications> -Maintenance-free type made by Optima Battery

■ Aero sports wiper blade
An aero type wiper blade is used for the main body.By adding a deflector with fins, the arm joint is aero-formed.The wind pressure generated during driving is positively received and the wiper lift is suppressed.The blade rubber is evenly adhered to the glass surface to improve visibility when driving at high speeds in the rain. >> More details

<Main specifications> ・ Driver side: 450mm ・ Passenger seat side: 480mm ・ Twin rail type

■ Door handle cover & protector set
A carbon-like matte design that protects the fragile door handle and gives it a sporty look.Pursuing high-quality details and achieving a natural and unified fitting.A package for one unit is available, and the door handle and protector can be purchased separately. >> More details

<Main specifications> ・ Carbon tone ・ Weather resistant ABS cover x 4 ・ PVC protector x 4 ・ One set

■Door handle protector
Made of carbon-like PVC that protects the paint around the door handle, which is easily damaged when opening and closing. The lineup includes three colors: black, silver, and red (a color similar to Soul Red Crystal Metallic) that can be selected according to the body color.>>Click here for part numbers and prices

<Main specifications> - Carbon-like AutoExe logo included - PVC double-sided tape adhesive - Left and right set

■antenna garnish
A dress-up item that makes the mass-produced shark fin antenna look fearless with its mechanical carbon pattern and AutoExe logo. The material is flexible PVC, and double-sided tape can be easily attached to the antenna body. *The antenna body is not included in the product.>> More details

<Main specifications> ・Carbon tone ・AutoExe logo included ・Made of PVC with double-sided tape ・Set of 2 left and right

■ Wheel nut set
Irregular heptagonal (heptagonal) small diameter type with an aluminum end cap with the AutoExe logo.The main body is made of high-strength black-painted chrome vanadium steel that does not easily loosen at high temperatures.The knurled red-colored aluminum end cap adds a subtle and sophisticated accent to your car's footwell.>> More details

<Main specifications> - Body: Made of chrome vanadium steel, black paint - Cap: Made of aluminum, red anodized + clear paint - AutoExe logo included - Irregular heptagon type, special adapter wrench included

■Air valve cap
Following the design of AutoExe wheel nuts, this product is made of aluminum with a red anodized finish, allowing you to enjoy a total coordination. The brass threads that are exposed on mass-produced plastic caps are covered to give a clean and sophisticated impression around the wheel.>> More details

<Main specifications> Aluminum, red anodized + clear coating with AutoExe logo (on both sides), set of 4

■Sports steering wheel (nappa leather)
A red-colored center mark with a flat bottom shape ... An airbag-compatible product that uses high-quality nappa leather as the material for outstanding sportiness.The elliptical cross-section grip with dimple processing that is not too thick and easy to grip, and the dimple-processed leather and thumb grip that improve holdability are created with details to actively enjoy driving.>> More details

<Main specifications> -Made of nappa leather-SRS airbag system / steering switch compatible-Flat bottom shape

■Sports steering wheel (genuine leather)
Sporty flat bottom shape.Specifications that are particular about details such as an oval cross-section grip that is easy to grip and a thumb grip that suppresses slippage.Emphasis is placed on operability and visibility, and the diameter is 370 mm, which is the same as that of mass-produced vehicles.>> More details

<Main specifications> -Flat bottom with a diameter of 370 mm-Red stitch-Compatible with genuine airbags / steering switches-Trade-in type

■ Carbon paddle shift lever
Made of high-quality real carbon that is mounted over the mass-produced steering shift switch.Improved operability by moderately increasing the size.The cockpit is made sporty by clarifying the response in sports driving.　>> More details

<Main specifications> ・ With AutoExe logo ・ Double-sided tape adhesive type ・ All 4 pieces configuration ・ Overall length 100mm (upper + 25mm lower + 10mm extension compared to mass production)

■ Shift knob (ball shape) for AT
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details

<Main specifications> ・For automatic transmission vehicles (straight type) ・Made of genuine leather ・Diameter: 51mm ・Total length: 87mm ・Push type ・Red stitching

■ Shift knob (ball shape) for MT
Made of genuine leather (nappa leather) with a diameter of 51 mm, with an emphasis on operability. The shift knob fits comfortably in the palm of your hand and can be held either sideways or upright. The height can be adjusted to suit your physique and preferences. The AutoExe logo is printed on the top.>> More details

<Main specifications> ・For manual transmission vehicles ・Made of genuine leather (nappa leather) ・Thread size: M10 x 1.25 ・Diameter: 51mm ・Total length: Adjustable from 70 to 88mm ・Stitching: Red/Black/Light Gray (3 colors available)

■ Shift knob (stick shape) for MT
Made of genuine leather (nappa leather) with a small diameter of 42 mm. The shift knob fits comfortably in the palm of your hand and can be held either sideways or upright. The height can be adjusted to suit your build and preferences. The AutoExe logo is printed on the top. >> More details

<Main specifications> ・For manual transmission vehicles ・Made of genuine leather (nappa leather) ・Screw size: manual transmission vehicles: M10 x 1.25 ・Diameter: 42mm ・Total length: adjustable from 73 to 91mm ・Stitching: red/black/light gray (3 colors available)