New release for new roadster.
Special specifications that give a feeling of bold performance.
Eye-catching tail end, thrilling acceleration feeling and exhaust note... Our "Sports Muffler" is a specification that gives top priority to exhaust efficiency by carefully examining the pipe diameter and venturi in consideration of the optimal layout for each car model. .The basic method of sound tuning is to create a propagation distance for sound waves, shift the phase, and interfere with the high and low frequencies (frequency) of the sound (see conceptual diagram).Silence that does not rely on sound absorbing materials such as glass wool (■(Except for RX-8) creates a clear and smooth sports sound up to the upper register.Theoretically, it is also a nice point that there is no change in volume due to aging.A slash tail with the tail end cut off and a perfect circular dual tail create a rear view with a sense of unity that is suitable for sports cars and SUVs.
<For CX-60>
Rear exhaust left and right 4 tail specifications to be installed at the same time as the exclusive muffler garnish.In terms of function, the highest priority is given to improving exhaust efficiency, and the multi-stage expansion type used in mass-produced vehicles has been changed to a straight structure to reduce back pressure loss.Examine the pipe layout and silencer capacity, etc., and get an agile response.By silencing without using glass wool, we have created a sports sound that is clear and well-defined even in the upper register.
<For RX-8 (SE3P-300001 to 6MT)>
Adopted a 90mm slash tail that tightens the rear view to Spartan.The silencer has been changed from the multi-stage expansion type of mass-produced vehicles to a straight structure to reduce back pressure loss.Improved exhaust efficiency, such as improving the suction effect by equipping the middle pipe with a chamber as standard equipment.It is a high-quality specification that has been refined down to the smallest detail.
<For CX-5 (KF series-500001 ~)>
Designed exclusively for the new CX-5 diesel vehicles.Aggressive 4-piece slash tail specification that can be installed at the same time as the muffler garnish.By muting without using glass wool, it creates a sport sound with good clearness without stagnation up to the high register.
<For Roadster (ND)>
Single
The combination of a slash tail with a sub-silencer and a diffuser-shaped rear under panel gives it a light feel (it can also be installed as a single muffler).
dual
Two left and right output specifications with a slash tail with a diameter of 76 mm. When installed at the same time as the special muffler garnish, it creates a rear view that is both specialized and has a sense of unity.
Center dual
Perfect circle φ90 × 2 Center dual type.In combination with the dedicated rear under panel, it completes a tight rear view that is typical of lightweight sports.
<For MAZDA3 FASTBACK (BP)>
Perfect circle φ80 Aggressive presence by combining the slash tail with 4 left and right and the exclusive muffler garnish.Designed exclusively for diesel / gasoline vehicles.
<For CX-5 (KF series-~ 499999) / CX-8 (KG)>
Perfect circle φ90 The combination of the dual tail with 4 left and right and the exclusive muffler garnish creates a powerful and fearless appearance.Designed exclusively for diesel / gasoline vehicles
<Product compatibility table>
■ Sports Muffler Stainless steel straight structural silencer
Car name | 適合 車 種 | Tail layout | part number | Tax-included price (Price without tax) | Main pipe diameter | Tail pipe diameter | Weight (Kg) | Codes | Reference work Time |
---|---|---|---|---|---|---|---|---|---|
RX-8 | SE3P-300001 ~ ※ 1 | Genuine same position | SEA1 V5 800 | ¥184,800 (¥ 168,000) | φ60.5 | 90mm (× 2) | 15.7 | F | 0.9 h |
Roadster | NDERE all cars/NDERC-300001~/ND5RE MT cars/ND5RC MT i-ELOOP no cars NDERE all cars/NDERC-300001~/ND5RE MT cars※ 2 NDERE/NDERC ※ 3 ND5RE MT car/ND5RC * 3 * 4 | Genuine same position dual Center dual Center dual | MND8Y70 NDA1 V5 800 MND8Y60 MND8Y50 | ¥126,500 (¥ 115,000) ¥162,800 (¥ 148,000) ¥140,800 (¥ 128,000) ¥140,800 (¥ 128,000) | φ50.0 φ50.0 φ54.0 φ54.0 | 90 mm 76mm (× 2) 90mm (× 2) 90mm (× 2) | 9.3 10.0 9.6 9.6 | F | 0.8 h |
MAZDA3 | BP8R/BP8P fastback car * 5 * 6 BPFJ3R/BPFJ3P fastback BPFP Fastback 2WD vehicle BP5R/BP5P Fastback 2WD vehicle ※ 5 | Left and right dual Left and right dual | MBP8Y50 MBP8Y60 | ¥134,200 (¥ 122,000) ¥158,400 (¥ 144,000) | φ60.5 | 80mm (× 4) | 9.7 11.4 | F | 0.7 h |
CX-5 | KF2P-500001 ~ AT car ※ 7 KF2P- ~ 499999 AT car ※ 8 KF5P-200001~499999/KFEP-200001~499999 * 8 * 9 | Left and right dual | MKF8Y90 MKF8Y70 MKF8Y80 | ¥134,200 (¥ 122,000) ¥140,800 (¥ 128,000) ¥162,800 (¥ 148,000) | φ60.5 | 90mm (× 4) | 7.8 8.0 14.8 | F | 0.7 h |
CX-60 | KH3R3P/KH3P ※ 10 KH5P ※ 10 | Left and right dual Left and right dual | KHA1 V5 800 KHA2 V5 800 | ¥134,200 (¥ 122,000) ¥206,800 (¥ 188,000) | φ60.5 | 80mm (× 4) | 9.0 15.6 | D | 0.8 h |
CX-8 | KG2P-~449999 ※ 11 KG5P-~349999 turbo 4WD/KG5P-~349999 NA2WD car ※ 11 | Left and right dual | MKG8Y50 MKG8Y60 | ¥140,800 (¥ 128,000) ¥162,800 (¥ 148,000) | φ60.5 | 90mm (× 4) | 8.0 15.6 | F | 0.7 h |
※ 1 Cannot be installed on 22AT / 4MT vehicles produced after April 6.
※ 2 Requires simultaneous installation of muffler garnish (NDA1 V3 910). In addition, part of the rear bumper must be removed for installation.
※ 3 It is necessary to install the rear under panel (MND2400) at the same time.In addition, it is necessary to partially cut off the rear bumper for installation.
※ 4 Cannot be installed on vehicles equipped with MT i-ELOOP from ND5RC-300001.
※ 5 It is necessary to install the muffler garnish (MBP2410) at the same time.In addition, it is necessary to partially cut off the rear bumper for installation.
※ 6 Cannot be installed on 2WD 16-inch vehicles of XD PROACTIVE and XD PROACTIVE Turing Selection.
※ 7 It is necessary to install the muffler garnish (MKF2470) at the same time.In addition, it is necessary to partially cut off the rear bumper for installation.
※ 8 It is necessary to install the muffler garnish (MKF2410) at the same time.In addition, it is necessary to partially cut off the rear bumper for installation.
※ 9 Cannot be installed on KF5P NA 4WD vehicles.
※ 10 Muffler garnish (KHA1 V3 910/KHA2 V3 910) must be installed at the same time.In addition, it is necessary to remove a part of the rear bumper for installation.
※ 11 It is necessary to install the muffler garnish (MKG2400A) at the same time.In addition, it is necessary to partially cut off the rear bumper for installation.
<Rear under panel/muffler garnish>
For Roadster Single Tail
For roadster dual muffler
For Roadster Center Dual Muffler
For MAZDA3
For CX-5 (KF series-~ 499999) / CX-8
For CX-5 (KF series-500001 ~)
for CX-60
<Product compatibility table>
■ Rear Under Panel / Muffler Garnish For vehicles equipped with a sports muffler Cannot be installed separately
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time |
---|---|---|---|---|---|---|
Rear under panel | Roadster (all ND series cars) | MND2410 | ¥46,200 (¥ 42,000) | Black satin (no painting required) Made by AES Drilling required | D | 0.5 h |
Muffler garnish | Roadster (NDERE/ND5RE) | NDA1 V3 910 | ¥46,200 (¥ 42,000) | Sports muffler for vehicles equipped with dual (NDA1 V5 800) Cannot be installed separately Made by AES Hole drilling required | D | 0.5 h |
Rear under panel | Roadster (NDERC / ND5RC) | MND2400 | ¥34,100 (¥ 31,000) | For vehicles equipped with Sports Muffler Center Dual (MND8Y50 / MND8Y60) Cannot be installed separately Piano Black Painted ABS resin Drilling required | D | 0.5 h |
Muffler garnish | MAZDA3 fastback | MBP2410 | ¥30,800 (¥ 28,000) | For vehicles with sports muffler (MBP8Y50 / 8Y60) Cannot be installed separately AES black satin finish (no painting required) Rear bumper excision required | D | 1.0 h |
Muffler garnish | CX-5 (KF series-500001 ~) | MKF2470 | ¥30,800 (¥ 28,000) | For vehicles equipped with sports muffler (MKF8Y90) Cannot be installed separately AES black satin finish (no painting required) Rear bumper excision required | D | 1.0 h |
Muffler garnish | CX-5 (KF series-~ 499999) | MKF2410 | ¥30,800 (¥ 28,000) | For vehicles with sports muffler (MKF8Y70 / 8Y80) Cannot be installed separately AES black satin finish (no painting required) Rear bumper excision required | D | 1.0 h |
Muffler garnish | CX-60 (KH3R3P) | KHA1 V3 910 | ¥30,800 (¥ 28,000) | For cars equipped with sports muffler (KHA1 V5 800) Cannot be installed separately Made by AES Black satin finish (no painting required) Rear bumper cutting required | D | 1.2 h |
Muffler garnish | CX-60 (KH3P/KH5P) | KHA2 V3 910 | ¥30,800 (¥ 28,000) | For cars equipped with sports muffler (KHA1 V5 800/KHA2 V5 800) Cannot be installed separately Made by AES Black satin finish (no painting required) Rear bumper cutting required | D | 1.2 h |
Muffler garnish | CX-8 (all KG series cars) | MKG2400A | ¥30,800 (¥ 28,000) | For vehicles with sports muffler (MKG8Y50 / 8Y60) Cannot be installed separately AES black satin finish (no painting required) Rear bumper excision required | D | 1.0 h |