Front bumper & grill

Bumper grill integrated type that realizes a markless face while maintaining the millimeter wave radar (SBS / MRCC) function. It also supports mass-produced headlamp washers installed in 4WD vehicles.

Rear roof spoiler

A wing type that can be double-mounted without removing the standard rear spoiler. AutoExe ornaments also add a crisp accent.

Sports side visor

A high-performance side visor with a ventilation mechanism in addition to rain and sun protection.When the recommended side window is open, the negative pressure generated during driving is used to actively discharge the indoor air.At the same time, it also has the effect of preventing the ingress of rainwater.

■ Lowdown spring
The styling is sporty and tightened in combination with a mass-produced damper, and the handling is improved by lowering the center of gravity.By suppressing the vehicle height to -20 mm and the spring constant to about 110%, the suspension stroke is secured and comfort is also taken into consideration.　>> More details

<Main specifications> ・ Vehicle height: -20mm ・ Spring constant isplease use this form. for more information.

Wearing gallery

■ Sports damper
Although it has the same shape as the mass-produced product, the internal piston adopts a "very low speed valve" that generates precise damping force from the moment it starts moving.It accurately controls changes in the vehicle's posture and achieves a sporty, flat and high-quality ride.It is recommended to use with genuine springs (can be used with lowdown springs).>> More details

<Main specifications> ・ Fixed gas damping force

■ Adjustable stabilizer link
When the vehicle height is down, the angle of the lower arm changes.As a result, the arm angle between the stabilizer and the link becomes an acute angle, which tends to spoil the original stabilizer effect.This product corrects the arm angle when the vehicle height is lowered by adjusting the link length.Optimize the stabilizer function.>> More details

<Main specifications> -Full length adjustable XNUMX-piece set-Front and rear settings.・ Axial mount type

■ Sports stabilizer
The left and right suspension arms are connected by a pipe, and the spring effect suppresses the amount of roll.Controllability during cornering is maintained by increasing the spring constant appropriately.It is especially effective when increasing the size of tires to high grip tires.For the front.　>> More details

<Main specifications> ・ For front ・ Solid Φ23.0 ・ Uses genuine mount

■ Strut tower bar
The first step to reinforce the body connecting the left and right strut towers.The steel oval shaft and one-piece structure, which are advantageous in terms of rigidity, ensure the highest level of strength for a general tower bar.It is effective when installed separately, but it is best used in combination with a floor crossbar.　>> More details

<Main specifications> -Steel oval shaft 2-piece structure XNUMX-point type

Wearing gallery

■ Center floor bar
It suppresses distortion near the center of the body monocoque, which cannot be compensated by strut tower bars and floor crossbars, and compensates for the "annular structure" effect of the SKYACTIV body.I try to have a low center of gravity layout that does not sacrifice the leg space of the rear seats as much as possible. 　>> More details

<Main specifications> -Steel oval shaft 1-piece structure 4-point type

Wearing gallery

■ Floor crossbar
An item that works like a rear tower bar by connecting the left and right sides of the rear floor.It is also a nice point to be able to utilize the high-strength seat mounting point to install it without sacrificing the utility of the luggage room at all. 　>> More details

<Main specifications> -Steel oval shaft 2-piece structure 3-point type

Wearing gallery

■ Lower arm bar
By connecting the bases of the left and right lower arms, which are the suspension mounting base points, with steel oval pipes, minute alignment changes are suppressed.Improves the feeling of handling.　>> More details

<Main specifications> -Steel oval shaft 1-piece structure 2-point type

Wearing gallery

■ Air filter replacement
Utilizing the air cleaner case of mass-produced cars, replacing only the filter part effectively improves the accelerator response.The dry filter, which has a good balance between ventilation performance and dust collection effect, is a disposable type that has little effect on the air flow sensor and is easy to maintain.　>> More details

<Main specifications> ・ Dry type ・ Disposable (disposable) type

■ Sports induction box
Use the air cleaner box of a mass-produced car to replace the case on the suction side.Directly guides fresh air to the air filter to improve intake efficiency.The sound also changes to sports-like.Further increase efficiency by combining with the optional K & N air filter.　>> More details

<Main specifications> -Funnel type FRP frame + aluminum heat shield

Wearing gallery

■ Ram air intake system
A high-end intake system that pursues efficiency and looks.The area of ​​the intake port of the fresh air duct has been expanded by 20% while following the basic layout of mass production that is not easily affected by the radiant heat of the radiator.By combining a 3-piece duct / large cleaner box with a straight path as much as possible and a dedicated cylindrical filter, the filling efficiency corresponding to the increased air is improved.Improves power and torque from the normal range.The appearance made of real carbon is also high quality.Compatible with diesel vehicles.　>> More details

<Main specifications>・Carbon air duct + dedicated air filter　

■ Intake suction kit
Specifications that secure the maximum effective flow path area of ​​intake air and reduce intake resistance.The material used is multi-layer polystar silicon, which has a high effect of suppressing deformation due to negative suction pressure.As a result, the accelerator response has been improved.The crimson coloring adds an accent to the engine room.>> More details

<Main specifications> ・ Made of 4-layer polystar silicon

Wearing gallery

■ Premier tail muffler
A series with a sophisticated and profound feeling. The 110X95mm oval-shaped tail end has a very mature texture.With a large-capacity straight structure silencer that has been carefully tuned for a narrow main pipe diameter and internal structure, it achieves both improved accelerator response from the practical range and a gentle sports sound that suppresses the noise of the room.　>> More details

<Main specifications> ・ Stainless steel ・ Straight structure silencer ・ Main diameter: Φ50.8 ・ Tail diameter: Φ110 × 95 × 2 ・ Weight: 9.5kg (2WD vehicle) /9.0kg (4WD vehicle) /11.7kg (gasoline vehicle) ) ・ Safety standard compliant product

[Sound library for audition] * You can compare it with the mass-produced muffler recorded under the same conditions.It may not be accurate due to the characteristics of the playback environment, but please watch it as a reference for changes in sound quality and volume.

Wearing gallery

■ Premier Tail Muffler Center Dual
Two oval-shaped tail ends are placed in the center.By installing it as a set with a dedicated rear under panel, it creates a sense of specialty and power.Cannot be installed independently. Designed exclusively for 2WD / 2WD.　>> More details

<Main specifications> ・ Stainless steel ・ Straight structure silencer ・ Pipe diameter: Ф50.8 ・ Tail diameter: Ф110 × 95 × 2 ・ Suitable for safety standards

■ Rear under panel
A set with a premier tail muffler.At the same time as covering the notch at the outlet of the mass-produced muffler, it realizes a rear view with a sense of unity with the muffler.

<Main specifications> -Dark gray painted-ABS resin

■ Exhaust finisher
A finisher that bolts on to the tail end of the genuine muffler.The oval shape, which is composed of thick and beautiful curves, renews the image of the conventional muffler cutter.It is ideal for users who want to add fashionability while keeping the genuine muffler.>> More details

<Main specifications> -Stainless steel-Set of 95 left and right-Tail Φ80 x XNUMX oval-AutoExe logo included

Wearing gallery

■ Street sports brake pads
The aim is "deceleration at will".Designed with an emphasis on stable effectiveness during continuous braking, delicate load transfer in cornering, and flexible control of vehicle speed, rather than simply stopping performance.Focus on the amount of change and how to change the coefficient of friction (μ), which constantly changes depending on various conditions such as pedaling force, speed, and temperature.The "transient characteristics of μ" required by sports-oriented drivers realizes a taste that is synchronized with the sensibilities.　>> More details

<Main specifications> ・ Non-asbestos friction material ・ Rotor proper temperature: 0 to 400 ℃

■ Street brake rotor
Mass-produced XNUMX-piece structure with the same shape FC Cast iron, but with improved strength by controlling the content of carbon and silicon.Further heat treatment is applied to stabilize the metal connective tissue.It suppresses distortion due to heat and improves fade resistance and crack resistance.　>> More details

<Main specifications> ・ 6 slits on one side ・ 1 piece type

■ Brake pedal brace
The bracket of the pedal mounting part, which causes slight distortion during brake operation, is three-dimensionally reinforced with steel braces to ensure rigidity.It improves the delay in reaction from when the pedal is pressed until the brake is applied, and contributes to a direct effect.　>> More details

<Main specifications> -Steel 2-piece structure

■ Sports clutch line
Uses stainless mesh PTFE (Teflon), which has less deterioration due to heat and aging and less expansion due to hydraulic pressure than the rubber used in mass-produced vehicles.Contributes to a direct clutch feel.In addition, PVC coating is applied to protect the hose for safety. >> More details

<Main specifications> -Stainless steel mesh PTFE + PVC coating

■ Sports oil filter
Fine sludge is removed by using a high-efficiency filter medium.By expanding the filtration area by about 5% compared to mass production, filtration efficiency is improved and pressure loss is reduced.Furthermore, by incorporating a powerful neodymium magnet, metal wear debris is captured without missing.It balances the functions required for oil filters at a high level.Dedicated to gasoline engine vehicles. >> More details

<Main specifications> ・ Built-in strong magnet ・ Filtration area expanded by about 5% compared to mass production

■ Turbo pipe
By optimizing the layout of the turbo pipe that guides the air supercharged by the turbine to the intercooler, and combining the aluminum elbow pipe whose inner wall is mirrored as much as possible and the 4-layer polyster silicon that has a high deformation suppressing effect, the hose expands due to pressurization. And suppresses the resistance of the air flow path.As a result, the boost pressure rises faster and turbo lag is reduced.Improve the response from the beginning of stepping on the accelerator.The product comes with a gasket required for installation. >> More details

<Main specifications> -Aluminum pipe (anodized) + silicon hose / band / gasket included

■ Oil filler cap
The oil filler cap has been changed from genuine resin to 52S aluminum, which is fully machined and full of craftsmanship.Brilliant red alumite processing is applied to give a mechanical and gorgeous accent to the engine room.The laser-engraved AutoExe logo is also a delicate impression.　>> More details

<Main specifications> ・ 52S aluminum fully machined ・ Red alumite processing ・ Laser engraved with AutoExe logo

■ Oil level gauge grip
An item that replaces the resin grip of a mass-produced oil level gauge with aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.DIY installation is possible with the attached dedicated tool. Compatible with a wide range of vehicles equipped with the SKYACTIV engine.　>> More details

<Main specifications> -Aluminum-Red alumite-With AutoExe logo-Includes a dedicated tool for mounting

■ Brake fluid cap
The resin mass-produced brake fluid tank cap has been upgraded to aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.Combined with an oil filler cap and level gauge grip with the same design, it accelerates the total coordination of the engine room.　>> More details

<Main specifications> -Aluminum-Fully machined-Red alumite processing-Laser engraved AutoExe logo included

■ Fuel cap cover
An ABS cover that can be attached over a mass-produced fuel cap.The design with cap bolts on bright Exe Red gives a gorgeous impression to the fuel filler port. With AutoExe logo.Compatible with a wide range of current Mazda vehicles.　>> More details

<Main specifications> ・ ABS red painted ・ With decorative cap bolt ・ With AutoExe logo ・ Double-sided tape attached ・ Fuel label / erroneous oil supply prevention reminder sticker included

■ Optima Battery
Synonymous with maintenance-free batteries, which boast a longer life than conventional open-type batteries.It is a completely sealed type that uses the original spiral cell technology, so there is no need to replenish the battery fluid.Provides a stable current even under high load.Can be installed without using additional adapters.>> More details

<Main specifications> -Maintenance-free type made by Optima Battery

■ Battery clamp
Playful in the engine room. Made of one-piece steel designed with the image of an AutoExe strut tower bar.The bright red color and logo plate have been faithfully reproduced.>> More details

<Main specifications> -Steel red paint-With AutoExe ornament

■ Aero sports wiper blade
An aero type wiper blade is used for the main body.By adding a deflector with fins, the arm joint is aero-formed.The wind pressure generated during driving is positively received and the wiper lift is suppressed.The blade rubber is evenly adhered to the glass surface to improve visibility when driving at high speeds in the rain. >> More details

<Main specifications> ・ Driver side: 550mm ・ Passenger seat side: 450mm ・ Twin rail type

■ Sports side visor
A high-performance side visor with a ventilation mechanism in addition to rain and sun protection.When the recommended side window is open, the negative pressure generated during driving is used to actively discharge the indoor air.At the same time, it also has the effect of preventing the ingress of rainwater.>> More details

<Main specifications> -Smoke type acrylic resin-Set of 4 left and right with AutoExe logo

Wearing gallery

■ Door handle cover & protector set
A carbon-like matte design that protects the fragile door handle and gives it a sporty look.Pursuing high-quality details and achieving a natural and unified fitting.A package for one unit is available, and the door handle and protector can be purchased separately. >> More details

<Main specifications> ・ Carbon tone ・ Weather resistant ABS cover x 4 ・ PVC protector x 4 ・ One set

■antenna garnish
A dress-up item that makes the mass-produced shark fin antenna look fearless with its mechanical carbon pattern and AutoExe logo. The material is flexible PVC, and double-sided tape can be easily attached to the antenna body. *The antenna body is not included in the product.>> More details

<Main specifications> ・Carbon tone ・AutoExe logo included ・Made of PVC with double-sided tape ・Set of 2 left and right

■ Wheel nut set
Irregular heptagonal (heptagonal) small diameter type with an aluminum end cap with the AutoExe logo.The main body is made of high-strength black-painted chrome vanadium steel that does not easily loosen at high temperatures.The knurled red-colored aluminum end cap adds a subtle and sophisticated accent to your car's footwell.>> More details

<Main specifications> - Body: Made of chrome vanadium steel, black paint - Cap: Made of aluminum, red anodized + clear paint - AutoExe logo included - Irregular heptagon type, special adapter wrench included

■ Sports steering wheel(Nappa leather)
A red-colored center mark with a flat bottom shape ... An airbag-compatible product that uses high-quality nappa leather as the material for outstanding sportiness.The elliptical cross-section grip with dimple processing that is not too thick and easy to grip, and the dimple-processed leather and thumb grip that improve holdability are created with details to actively enjoy driving.>> More details

<Main specifications> -Made of nappa leather-SRS airbag system / steering switch compatible-Flat bottom shape

■ Sports steering wheel (genuine leather)
Sporty flat bottom shape.Specifications that are particular about details such as an oval cross-section grip that is not too thick and easy to grip, and a thumb grip that suppresses slippage.With an emphasis on operability and visibility, the diameter is 370 mm, which is the same as mass-produced vehicles.>> More details

<Main specifications> -Flat bottom with a diameter of 370 mm-Red stitch-Compatible with genuine airbags / steering switches-Trade-in type

■ Carbon paddle shift lever
Made of high-quality real carbon that is mounted over the mass-produced steering shift switch.Improved operability by moderately increasing the size.The cockpit is made sporty by clarifying the response in sports driving.　>> More details

<Main specifications> ・ With AutoExe logo ・ Double-sided tape adhesive type ・ All 4 pieces configuration ・ Overall length 100mm (upper + 25mm lower + 10mm extension compared to mass production)

■ Shift knob (spherical shape / genuine leather)
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details

<Main specifications> -For AT cars (straight type) -Made of genuine leather-Weight: 130g

■ Shift knob (spherical shape / genuine leather)
Made of genuine leather with a diameter of 51 mm with an emphasis on operability.A shift knob that fits easily in the palm of your hand and can be gripped on either the top or the side.You can adjust the height according to your physique and taste.AutoExe logo on the top.>> More details

<Main specifications> -For MT vehicles-Made of genuine leather-Screw size MT vehicles: M10 x 1.25-Weight: 190g

■ Shift knob (genuine leather)
Small diameter size with a diameter of 42 mm.A shift knob that fits easily in the palm of your hand and can be gripped on either the top or the side.You can adjust the height according to your physique and taste.Two types of stitches, red stitch and black stitch, can be selected.AutoExe logo on the top. >> More details

<Main specifications> -For MT vehicles-Made of genuine leather-Screw size MT vehicles: M10 x 1.25-Weight: 190g

■ Carbon number frame
Autoclave molded dry carbon license plate frame with dramatically improved material and design.UV cut clear coat finish that suppresses deterioration due to ultraviolet rays.A stainless steel AutoExe logo plate is placed in the center.　>> More details

<Main specifications> -Autoclave molded dry carbon-UV cut clear coating finish-Stainless steel AutoExe logo plate included

■carbon number bolt
High quality number bolt set using dry carbon for the plate part. Dress up your license plate smartly with the 3-piece configuration of our unique low-head stainless steel bolt/carbon washer.>> More details

<Main specifications> - Made of CFRP (logo plate part: dry carbon) - UV cut clear coating finish - Stainless steel low head bolt - AutoExe logo included - Set of 1 for 3 car

■ Leather key holder
Just fit to the new advanced key.The outer skin is made of black cordovan, which has excellent durability.Soft red cowhide leather is used on the inside to gently wrap the smart key.Handmade specifications jointly planned with the pioneering system notebook brand "ASHFORD".　>> More details

<Main specifications> Cordovan (horse leather) Made of cowhide AutoExe/ASHFORD embossed logo

■ Fragment case
Old and new advanced keys/card type keys can be stored.Based on black cordovan, which has excellent durability, perforated leather with red permeation expresses a sporty feeling.With card storage case + key chain.Handmade specifications jointly planned with the pioneering system notebook brand "ASHFORD".　>> More details

<Main specifications> Cordovan (horse leather), cow leather, AutoExe/ASHFORD embossed logo

■ Carbon key cover
Dedicated to the new advanced key.Autoclave manufacturing method used for racing car bodies, etc. Made of dry carbon.The texture that makes the most of the texture of the material is attractive.　>> More details

<Main specifications> -Made of dry carbon-With AutoExe logo-2-piece configuration-Double-sided tape adhesive type

■ Key case
A high-quality black suede-like key case compatible with conventional advanced keys.A cover type that firmly protects the key body from scratches and impacts.Red stitching and red lines give a sporty and delicate impression.　>> More details

<Main specifications> ・ Black suede tone ・ Red stitch ・ With AutoExe logo

■ Car verification case
High-quality black suede-like that smartly stores in-vehicle documents such as vehicle verification, instruction manuals, and maintenance notes.The red stitching, which is unified to the liner inside the case, also enhances the sports mind.　>> More details

<Main specifications> -Black suede tone-Red stitch-AutoExe embossed logo-Size: 245 x 180 x 65 mm

■ Ornaments / stickers
You can enjoy it with your own taste.It is also good to dress up with the demo car as a model.
A lineup of high-quality AutoExe logo decorations that make you feel the commitment to driving.　>> More details