■ Adjustable stabilizer link
When the vehicle height is down, the angle of the lower arm changes.As a result, the arm angle between the stabilizer and the link becomes an acute angle, which tends to spoil the original stabilizer effect.This product corrects the arm angle when the vehicle height is lowered by adjusting the link length.Optimize the stabilizer function.>> More details

<Main specifications> -Full length adjustable XNUMX-piece set-Front and rear settings.・ Axial mount type

■ Sports stabilizer
A stabilizer that connects the left and right suspension arms with a pipe and suppresses roll by the spring effect.This product has moderately strengthened spring rate from mass production.Stabilizes the posture when cornering while keeping controllability.Since the spring effect hardly occurs when going straight, the effect on the ride quality is minimal.>> More details

<Main specifications> ・ Front / rear settings ・ Front: Solid Φ24.0 ・ Rear: Solid Φ19.0 (2WD car) / Solid Φ20.0 (4WD car)

■ Sports tie rod end
The tie rod that connects the steering and the left and right knuckles of the front wheels is designed based on the genuine vehicle height.Therefore, the angle of the tie rod changes when the vehicle height is lowered, which induces a toe change during cornering.This product is an item that restores the original steering characteristics by correcting the tie rod angle during lowdown.>> More details

<Main specifications> -Carbon steel (S45C / forged) -Set of 2 left and right
Wearing gallery

■ Center floor bar
It suppresses distortion near the center of the body monocoque, which cannot be compensated by strut tower bars and floor crossbars, and compensates for the "annular structure" effect of the SKYACTIV body.I try to have a low center of gravity layout that does not sacrifice the leg space of the rear seats as much as possible.>> More details

<Main specifications> -Steel oval shaft 1-piece configuration 4-point type
Wearing gallery

■ Lower arm bar (front)
In mass-produced vehicles, deformation is suppressed by connecting the bases of the left and right lower arms, which are the suspension mounting base points of the open structure, with steel oval pipes.Supports accurate handling by regulating unnecessary alignment changes.Recommended for use with strut tower bars, floor cross bars, etc.>> More details

<Main specifications> -Steel oval shaft 1-piece structure 2-point type
Wearing gallery

■ Lower arm bar (rear)
In mass-produced vehicles, deformation is suppressed by connecting the bases of the left and right lower arms, which are the suspension mounting base points of the open structure, with steel oval pipes.Supports accurate handling by regulating unnecessary alignment changes.Recommended for use with floor crossbars.>> More details

<Main specifications> -Steel oval shaft 1-piece structure 2-point type
Wearing gallery

■ Member brace set
An evolved version of the lower arm bar.By mounting a steel frame with a three-dimensional truss structure on the body floor, the chassis rigidity of the highest level as a bolt-on part is obtained.In combination with the tower brace that reinforces the front and back of the upper part of the body, a tough monocoque body with two upper and lower stages is completed.Front and back set.V

<Main specifications> -Steel oval shaft with all 6 pieces
Wearing gallery

■ Motion control beam
Reinforces the front and rear ends of the body to increase torsional rigidity.By suppressing the vibration of the body due to high rigidity with an ultra-high damping friction type damper, it creates a street-best ride with strength and suppleness.A set of two front and back.>> More details

<Main specifications> ・ Friction type damper + steel shaft ・ With special mounting bracket
Wearing gallery

■ Air filter replacement
A genuine shape product that easily and effectively improves intake efficiency by utilizing the air cleaner box of mass-produced vehicles.The drywall with excellent breathability has little effect on the airflow sensor and is easy to maintain.Disposable type and reasonable price.>> More details

<Main specifications> -Dry type-Disposable (disposable) type

■ Sports induction box
Use the air cleaner box of a mass-produced car to replace the case on the suction side.Directly guides fresh air to the air filter to improve intake efficiency.The sound also changes to sports-like.Further increase efficiency by combining with the optional K & N air filter.>> More details

<Main specifications> -Funnel type FRP frame + aluminum heat shield

■ Ram air intake system
A high-end intake system that pursues efficiency and looks.While following the basic layout of mass production that is not easily affected by the radiant heat of the radiator, the suction port area of ​​the fresh air duct has been expanded by 50%.By combining a 3-piece duct / large cleaner box with a straight path as much as possible and a dedicated cylindrical filter, the filling efficiency corresponding to the increased air is improved.Improves power and torque from the normal range.The appearance made of real carbon is also high quality.>> More details

<Main specifications>・Carbon air duct + dedicated air filter
Wearing gallery

■ Intake suction kit
Specifications that secure the maximum effective flow path area of ​​intake air and reduce intake resistance.The material used is multi-layer polystar silicon or FRP pipe, which has a high effect of suppressing deformation due to suction negative pressure.As a result, the accelerator response has been improved.The crimson coloring adds an accent to the engine room.>> More details

<Main specifications> -Made of FRP / 4-layer polystar silicon hose-Detailed specificationsplease use this form. for more information.
Wearing gallery

■ Exhaust chamber kit
The aim of the intermediate exhaust pipe kit with a built-in chamber mechanism is to expand the "suction effect (pulsation effect)".Exhaust efficiency is improved by properly laying out a specially sized chamber.It is possible to install the parts individually, but we recommend using them together with the AutoExe muffler. >> More details

<Main specifications> ・ Main pipe diameter: Φ60.5 ・ Chamber diameter: Φ89.1 ・ 2-split type

■ Exhaust finisher
A finisher that bolts on to the tail end of the genuine muffler.The oval shape, which is composed of thick and beautiful curves, renews the image of the conventional muffler cutter.It is ideal for users who want to add fashionability while keeping the genuine muffler.>> More details

<Main specifications> -Stainless steel-Set of 95 left and right-Tail Φ80 x XNUMX oval-AutoExe logo included
Wearing gallery

■ Street sports brake pads
The aim is "deceleration at will".Designed with an emphasis on stable effectiveness during continuous braking, delicate load transfer in cornering, and flexible control of vehicle speed, rather than simply stopping performance.Focus on the amount of change and how to change the coefficient of friction (μ), which constantly changes depending on various conditions such as pedaling force, speed, and temperature.The "transient characteristics of μ" required by sports-oriented drivers realizes a taste that is synchronized with the sensibilities.>> More details

<Main specifications> ・ Non-asbestos friction material ・ Rotor proper temperature: 0 to 400 ℃

■ Street brake rotor
Mass-produced XNUMX-piece structure with the same shape FC Cast iron, but with improved strength by controlling the content of carbon and silicon.Further heat treatment is applied to stabilize the metal connective tissue.It suppresses distortion due to heat and improves fade resistance and crack resistance.>> More details

<Main specifications> ・ 6 slits on one side ・ 1 piece type
Wearing gallery

■ Brake pedal brace
The bracket of the pedal mounting part, which causes slight distortion during brake operation, is three-dimensionally reinforced with steel braces to ensure rigidity.It improves the delay in reaction from when the pedal is pressed until the brake is applied, and contributes to a direct effect.>> More details

<Main specifications> -Steel 2-piece structure

■ Sports oil filter
Fine sludge is removed by using a high-efficiency filter medium.By expanding the filtration area by about 5% compared to mass production, filtration efficiency is improved and pressure loss is reduced.Furthermore, by incorporating a powerful neodymium magnet, metal wear debris is captured without missing.It balances the functions required for oil filters at a high level.Dedicated to gasoline engine vehicles. >> More details
<Main specifications> ・ Built-in strong magnet ・ Filtration area expanded by about 5% compared to mass production

■ Oil filler cap
The oil filler cap has been changed from genuine resin to 52S aluminum, which is fully machined and full of craftsmanship.Brilliant red alumite processing is applied to give a mechanical and gorgeous accent to the engine room.The laser-engraved AutoExe logo is also a delicate impression.　>> More details

<Main specifications> ・ 52S aluminum fully machined ・ Red alumite processing ・ Laser engraved with AutoExe logo

■ Oil level gauge grip
An item that replaces the resin grip of a mass-produced oil level gauge with aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.DIY installation is possible with the attached dedicated tool. Compatible with a wide range of vehicles equipped with the SKYACTIV engine.　>> More details

<Main specifications> -Aluminum-Red alumite-With AutoExe logo-Includes a dedicated tool for mounting

■ Brake fluid cap
The resin mass-produced brake fluid tank cap has been upgraded to aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.Combined with an oil filler cap and level gauge grip with the same design, it accelerates the total coordination of the engine room.　>> More details
<Main specifications> -Aluminum-Fully machined-Red alumite processing-Laser engraved AutoExe logo included

■ Fuel cap cover
An ABS cover that can be attached over a mass-produced fuel cap.The design with cap bolts on bright Exe Red gives a gorgeous impression to the fuel filler port. With AutoExe logo.Compatible with a wide range of current Mazda vehicles.　>> More details

<Main specifications> ・ ABS red painted ・ With decorative cap bolt ・ With AutoExe logo ・ Double-sided tape attached ・ Fuel label / erroneous oil supply prevention reminder sticker included

■ Optima Battery
Synonymous with maintenance-free batteries, which boast a longer life than conventional open-type batteries.It is a completely sealed type that uses the original spiral cell technology, so there is no need to replenish the battery fluid.Provides a stable current even under high load.Can be installed without using additional adapters.>> More details

<Main specifications> -Maintenance-free type made by Optima Battery

■ Battery clamp
Playful in the engine room. Made of one-piece steel designed with the image of an AutoExe strut tower bar.The bright red color and logo plate have been faithfully reproduced.>> More details

<Main specifications> -Steel red paint-With AutoExe ornament

■ Aero sports wiper blade
An aero type wiper blade is used for the main body.By adding a deflector with fins, the arm joint is aero-formed.The wind pressure generated during driving is positively received and the wiper lift is suppressed.The blade rubber is evenly adhered to the glass surface to improve visibility when driving at high speeds in the rain. >> More details

<Main specifications> ・ Driver side: 600mm ・ Passenger seat side: 450mm ・ Twin rail type

■ Door handle cover & protector set
A carbon-like matte design that protects the fragile door handle and gives it a sporty look.Pursuing high-quality details and achieving a natural and unified fitting.A package for one unit is available, and the door handle and protector can be purchased separately.>> More details

<Main specifications> ・ Carbon tone ・ Weather resistant ABS cover x 4 ・ PVC protector x 4 ・ One set

■Antenna garnish
A dress-up item that makes the mass-produced shark fin antenna look fearless with its mechanical carbon pattern and AutoExe logo. The material is flexible PVC, and double-sided tape can be easily attached to the antenna body. *The antenna body is not included in the product.>> More details
<Main specifications> ・Carbon tone ・AutoExe logo included ・Made of PVC with double-sided tape ・Set of 2 left and right

■ Wheel nut set
Irregular heptagonal (heptagonal) small diameter type with an aluminum end cap with the AutoExe logo.The main body is made of high-strength black-painted chrome vanadium steel that does not easily loosen at high temperatures.The knurled red-colored aluminum end cap adds a subtle and sophisticated accent to your car's footwell.>> More details
<Main specifications> - Body: Made of chrome vanadium steel, black paint - Cap: Made of aluminum, red anodized + clear paint - AutoExe logo included - Irregular heptagon type, special adapter wrench included

■ Sports steering wheel
Sporty flat bottom shape.Specifications that are particular about details such as an oval cross-section grip that is not too thick and easy to grip, and a thumb grip that suppresses slippage.With an emphasis on operability and visibility, the diameter is 370 mm, which is the same as mass-produced vehicles.>> More details

<Main specifications> -Flat bottom with a diameter of 370 mm-Red stitch-Compatible with genuine airbags / steering switches-Trade-in type
Wearing gallery

■ Carbon paddle shift lever
Made of high-quality real carbon that is mounted over the mass-produced steering shift switch.Improved operability by moderately increasing the size.The cockpit is made sporty by clarifying the response in sports driving.　>> More details
<Main specifications> ・ With AutoExe logo ・ Double-sided tape adhesive type ・ All 4 pieces configuration ・ Overall length 100mm (upper + 25mm lower + 10mm extension compared to mass production)

■ Shift knob (spherical shape / genuine leather)
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details

<Main specifications> -For AT cars (straight type) -Made of genuine leather-Weight: 130g
Wearing gallery

■ Shift knob (spherical shape / genuine leather)
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details

<Main specifications> -For AT cars (gate type) -Made of genuine leather-Screw size: M8 x 1.25-Weight: 190g

■ Shift knob (genuine leather)
Small diameter size with a diameter of 42 mm.A shift knob that fits easily in the palm of your hand and can be gripped on either the top or the side.You can adjust the height according to your physique and taste.Two types of stitches, red stitch and black stitch, can be selected.AutoExe logo on the top. >> More details

<Main specifications> -Made of genuine leather-Screw size: M8 x 1.25-Weight: 190g
Wearing gallery

■ Carbon number frame
Autoclave molded dry carbon license plate frame with dramatically improved material and design.UV cut clear coat finish that suppresses deterioration due to ultraviolet rays.A stainless steel AutoExe logo plate is placed in the center.　>> More details
<Main specifications> -Autoclave molded dry carbon-UV cut clear coating finish-Stainless steel AutoExe logo plate included

■Carbon number bolt
High quality number bolt set using dry carbon for the plate part. Dress up your license plate smartly with the 3-piece configuration of our unique low-head stainless steel bolt/carbon washer.　>> More details
<Main specifications> - Made of CFRP (logo plate part: dry carbon) - UV cut clear coating finish - Stainless steel low head bolt - AutoExe logo included - Set of 1 for 3 car

■ Fragment case
Advanced key/card type key can be stored.Based on black cordovan, which has excellent durability, perforated leather with red permeation expresses a sporty feeling.With card storage case + key chain.Handmade specifications jointly planned with the pioneering system notebook brand "ASHFORD".　>> More details
<Main specifications> Cordovan (horse leather), cow leather, AutoExe/ASHFORD embossed logo

■ Key case
A high-quality black suede-like key case compatible with conventional advanced keys.A cover type that firmly protects the key body from scratches and impacts.Red stitching and red lines give a sporty and delicate impression.　>> More details
<Main specifications> ・ Black suede tone ・ Red stitch ・ With AutoExe logo

■ Car verification case
High-quality black suede-like that smartly stores in-vehicle documents such as vehicle verification, instruction manuals, and maintenance notes.The red stitching, which is unified to the liner inside the case, also enhances the sports mind.　>> More details
<Main specifications> -Black suede tone-Red stitch-AutoExe embossed logo-Size: 245 x 180 x 65 mm

■ Ornaments / stickers
You can enjoy it with your own taste.It is also good to dress up with the demo car as a model.
A lineup of high-quality AutoExe logo decorations that make you feel the commitment to driving.　>> More details