MAZDA2 / Demio Update Information
DJ-07
Mass production sports to further athletes.
DJ-2 debut for the new MAZDA07.
The new MAZDA2, which has a variety of grades and expands its lively personality.The revival of the traditional naming "Sport" is good news for those who want to run.Of course, we at Auto Exe, who have built numerous sports versions of Demio and MAZDA2 over the years, would like to offer the ability to immerse yourself in driving by leveraging a lightweight and compact body to handle the car with agility and briskness... The latest tuning kit DJ-07 was born out of such desire.
First of all, the styling goes to a more fearless aeroform.Based on the three items of front, side, and rear under that make the bottom end wide and low, the fin-type grille with a deeper three-dimensional effect, the rear side cowl with a bold design that reflects the flow of the wind, etc. have transformed into an athlete. there is
In terms of maneuverability, for example, total tuning is aimed at the cheerfulness that makes you smile just by clearing one tight corner at an intersection in the city or at a mountain pass.With the "Street Best Sports" specification as the core that considers comfort in everyday use, the full lineup includes options up to the high limit "High Limit Sports" with circuit driving in mind.From light tuning to full-fledged complete specifications depending on the desired driving.I want you to polish your MAZDA2 to a more fun and dynamic one.
Front under spoiler
Designed exclusively for new models.A dynamic form that weaves the high nose and forward wingtips adds an elegant strength.Painted piano black.
Front under spoiler dimensional drawing
The stated dimensions are the difference from the mass production bumper.Please use it as a guide when installing a styling kit such as road clearance.
Front grill
Designed exclusively for new models.A fin type with a horizontal tone that emphasizes the depth of carving.Piano black is applied to the surface, matte black paint is applied to the concave part, and the Mazda emblem is traded in.
Side under spoiler
A sense of stability is added to the side view bottom line of the compact body.Painted piano black.Equipped with AutoExe ornaments on the left and right.
Rear side cowl
Boldly design the flow of wind with a duct motif.Give it a sporty accent. (Aero Gray M / Soul Red Crystal M / Machine Gray Premium M painted products are set)
Rear under panel
A diffuser design with a three-dimensional effect that tightens the rear view in a sporty manner.Finished with glossy piano black paint.
Rear roof spoiler
The sporty wing-type design gives a powerful rear view.Painted piano black. Equipped with AutoExe ornament.
Sports side visor
Equipped with a ventilation mechanism that actively discharges the air inside the vehicle by using the negative pressure generated during driving.
Fuel lid cover
A mechanical one-point item that gives off a metallic feel.Double-sided tape is attached to the mass-produced fuel lid cover.
Door handle cover & protector set
A matte carbon finish that protects the paint on the door handle and gives the styling a sporty look.
The product is compatible with each safety equipment such as millimeter wave radar (SBS / MRCC), but it may not operate properly depending on the weather and driving conditions as well as mass-produced vehicles.
■ DJ-07 Styling Kit For MAZDA2 (DJ system)
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time |
---|---|---|---|---|---|---|
Front under spoiler | MAZDA2 ※ 1 | DJA2 V4 900 | ¥90,200 (¥ 82,000) | Piano black painted PPE required hole drilling | D | 1.4 h |
Front grill | MAZDA2 ※ 1 | DJA1 V4 220 | ¥90,200 (¥ 82,000) | Piano Black / Matte Black 2 Colors Painted AutoExe Ornament Included ABS Resin * 2 * 3 | F | 1.0 h |
Side under spoiler | All MAZDA2 cars | DJA1 V4 910 | ¥93,500 (¥ 85,000) | Piano Black Painted AutoExe Ornament Included Made of PPE | D | 1.7 h |
Rear side cowl | All MAZDA2 cars | DJA1 V3 060 2M DJA1 V3 060 C7 DJA1 V3 060PR DJA1 V3 060BB | ¥63,800 (¥ 58,000) ¥63,800 (¥ 58,000) ¥63,800 (¥ 58,000) ¥52,800 (¥ 48,000) | machine gray premium metallic painted ※ 4 Made of ABS, left and right set, double-sided tape adhesive Aero gray metallic painted ※ 4 Made of ABS, left and right set, double-sided tape adhesive Soul Red Crystal Metallic Painted ※ 4 Made of ABS, left and right set, double-sided tape adhesive Painting required ABS made Left and right set Adhesion with double-sided tape | D | 0.5 h |
Rear under panel | All MAZDA2 cars | DJA2 V3 300 | ¥57,200 (¥ 52,000) | Piano black painted ABS made | D | 0.8 h |
Rear roof spoiler | All MAZDA2 cars | DJA1 V4 920 | ¥83,600 (¥ 76,000) | Piano black painted AutoExe ornament included FRP required hole drilling | D | 1.0 h |
Sports side visor | All MAZDA2 cars | DJA1 V3 700 | ¥18,700 (¥ 17,000) | Smoke acrylic resin 4 piece set with ventilation mechanism | D | 0.5 h |
Fuel lid cover | All MAZDA2 cars | DJA1 V3 020 | ¥11,000 (¥ 10,000) | ABS chrome plated AutoExe logo double-sided tape adhesive | D | 0.3 h |
Door handle cover & protector set | All MAZDA2 cars | KFA1 V3 110 | ¥29,260 (¥ 26,600) | Carbon-like weatherproof ABS cover x 4 PVC protector x 4 XNUMX set | D | 1.0 h |
※ 1 DJ5FS-~699999/DJ5AS-~699999/DJLFS-~799999/DJLAS-~299999).
※ 2 A part of the front grill may be reflected on the screen of the front monitor.Also, when installed on a vehicle with a 360° view monitor, it may be necessary to adjust the aiming of the camera.
※ 3 In the case of vehicles with panel-type grilles with bright paint colors, the paint color of the genuine ultrasonic sensor may stand out.In that case, it is recommended to replace with a genuine Ultrasonic sensor (GMC8-67-UC1) x 2 separately.
■4 The paint color may not exactly match the body color.
<For customers considering simultaneous installation when purchasing a new car>
Some styling kits and functional parts are available as Mazda dealer options.For details, see the Mazda Motor Corporation website.[Accessory lineup]Also, please visit the sales staff of the sales company.
DJ-06
DJ-2 corresponding to MAZDA06 before facelift.While preserving the aesthetics and quality of the mass-production specification, the styling kit focused on enhancing the agility and sportiness, eliminating the glitter and blacking out.With a clean, horizontal markless grille and additional type front and rear spoilers, the fearless look exudes a high-quality athleticism, unleashing your MAZDA2 into a rugged appearance and driving performance.
Styling kit
Front under spoiler
An additional type to be attached to the mass-produced front bumper.The wedge shape at the tip of the wing adds graceful strength.Piano black painted.
Front grill
A three-dimensional markless grille with piano black on the surface and matte black paint on the recesses.It supports millimeter-wave radar (SBS / MRCC) and 360 ° view monitor function.
Rear under panel
Additional type to be attached to mass-produced rear bumpers.Black satin finish that does not require painting.Tighten the rear view with the rear roof spoiler.
Rear roof spoiler
A wing type with an attractive dynamic feeling that is typical of a sports compact.The AutoExe ornament attached to the center also adds a unique accent.
Sports side visor
High-performance visor with ventilation mechanism.The negative pressure generated during driving is used to actively exhaust the air inside the vehicle.A set of 4 front and back.
DJ-06 Front Under Spoiler Dimensional Drawing
The stated dimensions are the difference from the mass production bumper.Please use it as a guide when installing a styling kit such as road clearance.
The product is compatible with each safety equipment such as millimeter wave radar (SBS / MRCC), but it may not operate properly depending on the weather and driving conditions as well as mass-produced vehicles.
Product name | 適合 車 種 (Model list) | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time |
---|---|---|---|---|---|---|
Front under spoiler | MAZDA2 ※ 1 | DJA1 V4 900 | ¥90,200 (¥ 82,000) | Piano black painted FRP made drilling required | D | 1.0 h |
Front grill | MAZDA2 ※ 1 | MDJ2510 | ¥90,200 (¥ 82,000) | Piano black / matte black 2 colors painted ABS resin ※ 2 | F | 1.0 h |
Rear under panel | MAZDA2 ※ 1 | DJA1 V3 300 | ¥46,200 (¥ 42,000) | Black satin (no painting required) Made by AES Drilling required | D | 0.5 h |
Rear roof spoiler | All MAZDA2 cars All MAZDA2 cars | DJA1 V4 920 MDJ2600 | ¥83,600 (¥ 76,000) ¥44,000 (¥ 40,000) | Piano black painted AutoExe ornament included FRP made drilling required Painting required AutoExe Ornament included FRP drilling required | D | 1.0 h |
Sports side visor | All MAZDA2 cars | DJA1 V3 700 | ¥18,700 (¥ 17,000) | Smoke acrylic resin 4 piece set with ventilation mechanism | D | 0.5 h |
※ 1 DJ5FS-700001~/DJ5AS-700001~/DJLFS-800001~/DJLAS-300001~) cannot be installed.
※ 2 A part of the front grill may be reflected on the screen of the front monitor.Also, when installed on a vehicle with a 360° view monitor, it may be necessary to adjust the aiming of the camera.
<Other Styling Kit>
Functional parts
Suspension
"A New Driving Sensation" Suspension is at the core of sporty driving.Our aim is to handle at will beyond the framework of mass-produced vehicles.For drivers who want to enjoy driving positively, it is not just hard and soft, but it provides a street best ride with refined dynamic sensitivity performance such as initial response at the time of steering and transient characteristics of roll. >> Read more
■ Lowdown spring
Gives a sense of dynamism to the styling and stabilizes handling by lowering the center of gravity.The dedicated design according to the power unit ensures an appropriate amount of down and suspension stroke.The spring constant is set in consideration of the damping ratio with the damper.It is recommended to use an adjustable stabilizer link that corrects the stabilizer arm angle during lowdown.>> More details
<Main specifications> ・ Vehicle height: -20mm ・ Spring constant isplease use this form. for more information.
■ Sports damper
Although it has the same shape as the mass-produced product, the internal piston adopts a "very low speed valve" that generates precise damping force from the moment it starts moving.It accurately controls changes in the vehicle's posture and achieves a sporty, flat and high-quality ride.It is recommended to use with genuine springs (can be used with lowdown springs).>> More details
<Main specifications> ・ Fixed gas damping force
■ Street Sports Suspension Kit
The best street model that AutoExe thinks.A twin tube damper that quickly raises the damping force from the very low speed range and controls the roll speed based on dynamic Kansei engineering. Achieves linear maneuverability without compromising ride quality, such as setting the vehicle height based on -15mm.>> More details
<Main specifications> -Full length adjustment type
■ Club Sports Suspension Kit
Hard specifications that cut down the comfort to the limit that we can tolerate and convert the margin to exercise performance.The standard vehicle height is -30mm.In order to maintain accurate operability even in winding and hard circuit driving, a monotube type inverted damper with excellent heat conversion ability and rigidity under high load and a series-wound spring with a spring constant that rises linearly are adopted.Creates a solid driving sensation with a high sense of change regardless of the speed range.>> More details
<Main specifications> ・ Vehicle height adjustment type
■ Adjustable stabilizer link
Adjustable link that corrects the deviation of the stabilizer arm angle that occurs when the vehicle height is lowered, such as installing a low down spring.The total length of the link connecting the stabilizer and the car body is adjusted to optimize the arm angle, and the original stabilizer function of the design value is restored.For the front.>> More details
<Main specifications> -Full length adjustable 2-piece set-For front
■ Sports stabilizer
A stabilizer that connects the left and right suspension arms with a pipe and suppresses roll by the spring effect.This product has moderately strengthened spring rate from mass production.Stabilizes the posture when cornering while keeping controllability.Since the spring effect hardly occurs when going straight, the effect on the ride quality is minimal.>> More details
<Main specifications> ・ For front ・ Solid Φ22.0
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Low down spring | Diesel 2WD car ※ 1 Gasoline 2WD car ※ 1 Diesel 4WD car ※ 1 | DJA1 V5 720 DJA2 V5 720 DJA3 V5 720 | ¥39,600 (¥ 36,000) ¥39,600 (¥ 36,000) ¥41,800 (¥ 38,000) | Vehicle height-20mm Spring constant: Fr: 23.9 Rr: 27.2N / mm Vehicle height-20mm Spring constant: Fr: 20.0 Rr: 27.2N / mm Vehicle height-20mm Spring constant: Fr: 22.4 Rr: 41.2N / mm | D | 1.7 h 1.7 h 2.1 h |
|
Sports damper | 2WD car ※ 2 | MDJ7700 | ¥66,000 (¥ 60,000) | Compatible with fixed damping force mass production springs / AutoExe springs | D | 1.5 h | |
Street Sports Suspension Kit | 2WD car * 1 * 2 4WD car * 1 * 2 | MDJ7850 MDJ7860 | ¥195,800 (¥ 178,000) | Vehicle height adjustment type Damping force fixed type Spring constant: Fr: 26.5 Rr: 26.5N / mm Vehicle height adjustment range (mm): -5 to -25 Vehicle height adjustment type Damping force fixed type Spring constant: Fr: 23.5 Rr: 43.1N / mm Vehicle height adjustment range (mm): -5 to -25 | D | 2.1 h 2.5 h |
|
Club Sports Suspension Kit | 2WD car ※ 1 | MDJ7970 | ¥294,800 (¥ 268,000) | Monotube full length adjustment type damping force 24 steps adjustment type Recommended vehicle height-30mm Spring constant: Fr: 78.4 Rr: 49.0N / mm | F | 1.9 h | |
Adjustable stabilizer link | front | All cars ※ 3 | MDE7605 | ¥24,200 (¥ 22,000) | Full length adjustable left and right set of 2 | D | 0.5 h |
Sports stabilizer | front | All cars ※ 4 | MDJ7600 | ¥28,600 (¥ 26,000) | Solid φ22.0 Spring constant (compared to mass-produced vehicles) 115% (diesel) 128% (gasoline) | D | 2.5 h |
※ 1 When installed in a car with a 360 ° view monitor, it may be necessary to adjust the aiming of the camera.
※ 2 MAZDA2に装着する場合、純正マウンティングラバー(DA6A-28-380)×2、純正バンプストッパー(DA6A-28-1A0A)×2が別途必要。
※ 3 When installing the Street Sports Suspension Kit (MDJ7850 / 7860) / Club Sports Suspension Kit (MDJ7970), it is not necessary to install the same product because of its functionality.
※ 4 When installing on DJ3FS / DJLFS / DJLAS, genuine stabilizer bush (KD61-34-156F) x 2 is required separately.
Bodysuit
In order to enhance the sense of unity between the driver and the car, tuning to train the body is the basis.By suppressing slight distortion of each part of the body due to input from the road surface such as during cornering, the movement of the suspension initial operating area absorbed by the distortion is drawn out, and handling with a direct feeling without delay of reaction from the moment when the steering is started Contribute to. >> Read more
■ Strut tower bar
The first step to reinforce the body connecting the left and right strut towers.The steel oval shaft and one-piece structure, which are advantageous in terms of rigidity, ensure the highest level of strength for a general tower bar.It is effective when installed separately, but it is best used in combination with a floor crossbar.>> More details
<Main specifications> -Steel 2-piece structure XNUMX-point type
■ Center floor bar
It suppresses distortion near the center of the body monocoque, which cannot be compensated by strut tower bars and floor crossbars, and compensates for the "annular structure" effect of the SKYACTIV body.I try to have a low center of gravity layout that does not sacrifice the leg space of the rear seats as much as possible.>> More details
<Main specifications> -Steel oval shaft 1-piece configuration 4-point type
■ Floor crossbar
An item that works like a rear tower bar by connecting the left and right sides of the rear floor.It is also a nice point to be able to utilize the high-strength seat mounting point to install it without sacrificing the utility of the luggage room at all.>> More details
<Main specifications> -Steel 3-piece structure XNUMX-point type
■ Lower arm bar (front)
By connecting the bases of the left and right lower arms, which are the suspension mounting base points, with steel oval pipes, minute alignment changes are suppressed.Improves the feeling of handling.>> More details
<Main specifications> -Steel oval shaft 1-piece structure 2-point type
■ Member brace set
An advanced version of the lower arm bar that strengthens the entire underfloor by installing a reinforcement frame in the three-dimensional direction around the suspension member.Supports accurate handling by suppressing changes in suspension geometry.In combination with the tower brace that reinforces the upper part of the body, a tough monocoque with two upper and lower stages is completed.Front and back set.>> More details
<Main specifications> ・ Steel oval shaft front and rear 3-piece configuration ・ Weight: 7.4kg
■ Motion control beam
Reinforces the front and rear ends of the body to increase torsional rigidity.By suppressing the vibration of the body due to high rigidity with a friction type damper with ultra-high damping, it creates a street best ride with strength and suppleness.A set of two front and back.With a dedicated mounting bracket.>> More details
<Main specifications> -Friction type damper + steel shaft Front and rear set with mounting bracket
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Strut tower bar | front | All cars ※ 1 | DJA1 V5 420 | ¥29,700 (¥ 27,000) | Steel 1-piece structure 2-point type | D | 0.5 h |
Center floor bar | 2WD car 4WD car | MDJ4D00 MDK4D00 | ¥35,200 (¥ 32,000) | Steel 1-piece structure 4-point type | D | 0.5 h | |
Floor crossbar | rear | 2WD car ※ 1 4WD car | MDJ4500 MDK4500A | ¥19,800 (¥ 18,000) | Steel 2-piece structure 3-point type | D | 0.8 h |
Lower arm bar | front | 2WD car ※ 1 4WD car | MDJ4B00 MDK4B00A | ¥19,800 (¥ 18,000) | Steel 1-piece structure 2-point type | D | 0.5 h |
Tower brace set | 2WD car ※ 1 | MDJ4800 | sold out. | Steel 6-piece structure 6-point front and rear set | D | 2.5 h | |
Member brace set | 2WD car ※ 1 | MDJ4700 | ¥66,000 (¥ 60,000) | Steel 3-piece structure 10-point front and rear set | D | 1.5 h | |
Motion control beam | 2WD car | MDJ4900 | ¥104,500 (¥ 95,000) | Front and rear set with friction damper + steel shaft mounting bracket | E | 1.5 h |
※ 1 The member brace set and lower arm bar cannot be installed at the same time.Alternatively, the tower brace set, strut tower bar, and floor crossbar cannot be installed at the same time.
Intake & Exhaust
In the intake / exhaust tune, which is directly linked to the pleasure of driving, the point is not to improve the peak power, but to react to instantly convey the driver's intention to the car.The accelerator response has been refined based on the air filter and muffler with moderately reduced resistance.The restrained sports sound also deepens communication between the driver and the car. >> Read more
■ Air filter replacement
A genuine shape product that easily and effectively improves intake efficiency by utilizing the air cleaner box of mass-produced vehicles.The drywall with excellent breathability has little effect on the airflow sensor and is easy to maintain.Disposable type and reasonable price.>> More details
<Main specifications> ・ Dry type ・ Disposable type
■ Sports induction box
Utilizing the air cleaner case of mass-produced cars, replacing only the filter part effectively improves the accelerator response.The dry filter, which has a good balance between ventilation performance and dust collection effect, is a disposable type that has little effect on the air flow sensor and is easy to maintain.>> More details
<Main specifications> -Funnel type FRP frame + aluminum heat shield
■ Ram air intake system
A high-end intake system that pursues efficiency and looks.The area of the intake port of the fresh air duct has been expanded by 20% while following the basic layout of mass production that is not easily affected by the radiant heat of the radiator.By combining a 3-piece duct / large cleaner box with a straight path as much as possible and a dedicated cylindrical filter, the filling efficiency corresponding to the increased air is improved.Improves power and torque from the normal range.The appearance made of real carbon is also high quality.Compatible with diesel vehicles.>> More details
<Main specifications>・Carbon air duct + dedicated air filter
■ Fresh air guide
The "Fresh Air Guide" is an item that supports the improvement of intake efficiency by directly capturing the running wind from the front of the vehicle body.By directly connecting the front grille, which does not have a clear intake path in mass-produced vehicles, to the air intake port installed at the top of the core support with a dedicated air duct, the effect of exhaust heat from radiators etc. is minimized, and fresh air is air cleanered. It is introduced in the box to improve the filling efficiency. >> More details
<Main specifications> -FRP red gel coat finish
■ Intake suction kit
Specifications that secure the maximum effective flow path area of intake air and reduce intake resistance.The material used is multi-layer polystar silicon, which has a high effect of suppressing deformation due to negative suction pressure.As a result, the accelerator response has been improved.The crimson coloring adds an accent to the engine room.>> More details
<Main specifications> -Made of FRP / 4-layer polystar silicon hose-Detailed specificationsplease use this form. for more information.
■ Premier tail muffler
A series with a sophisticated and profound feeling. The 95X80mm oval-shaped tail end has a very mature texture.With a large-capacity straight structure silencer that has been carefully tuned for a narrow main pipe diameter and internal structure, it achieves both improved accelerator response from the practical range and a gentle sports sound that suppresses the noise of the room.>> More details
<Main specifications> ・ Stainless steel ・ Main diameter: Φ50.8 ・ Tail diameter: Φ95 × 80 ・ Safety standard compliant product
■ Exhaust finisher
A finisher that is bolt-on mounted on the muffler tail end of mass-produced vehicles.The oval shape, which is composed of thick and beautiful curves, has a high fit and renews the image of a general-purpose muffler cutter.Ideal for users who want to add fashionability while maintaining the functionality and sound.>> More details
<Main specifications> -Stainless steel-Set of 95 left and right-Tail Φ80 x XNUMX oval-AutoExe logo included
Product name | 適合 車 種 (Model list) | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Air filter replacement | All cars | MBM9A00 | ¥9,350 (¥ 8,500) | Dry-type disposable (disposable) type | D | 0.3 h | |
Sports induction box | No filter No filter | Diesel Car Gasoline 2WD car | MDJ957 MBZ957 | ¥33,000 (¥ 30,000) ¥38,500 (¥ 35,000) | Funnel type FRP frame + aluminum heat shield | D | 1.0 h |
Sports induction box | With filter With filter | Diesel Car Gasoline 2WD car | MDJ957X MBZ957X | ¥44,000 (¥ 40,000) ¥49,500 (¥ 45,000) | Funnel type FRP frame + aluminum heat shield K & N air filter included | D | 1.0 h |
Ram air intake system | Diesel Car | MDJ9590 | ¥104,500 (¥ 95,000) | Carbon air duct + carbon/FRP box Dedicated air filter included | F | 1.0 h | |
Fresh air guide | DJ system (excluding MAZDA2)※ 1 | MDJ9B00 | ¥35,200 (¥ 32,000) | FRP 2-piece configuration Red gel coat finish | D | 1.0 h | |
Intake suction kit | Diesel Car Gasoline car ※ 5 | MDJ961 MBM962 | ¥16,500 (¥ 15,000) ¥17,600 (¥ 16,000) | Silicone hose | D D | 0.2 h 0.3 h |
|
Premier tail muffler | Single Single | DJ5FS ※ 2 DJLFS / DJ3FS ※ 3 | DJA1 V5 810 DJA2 V5 810 | ¥79,200 (¥ 72,000) | Stainless steel main pipe diameter φ50.8 Tail diameter 95 × 80mm | D | 0.7 h |
Rear under panel (For installing the center dual muffler) | DJ5FS-~ 599999 / DJ3FS ※ 4 | MDJ2420 | ¥33,000 (¥ 30,000) | Made of ABS resin Dark gray painted Drilling required | D | 0.5 h | |
Exhaust finisher | Car with genuine muffler cutter No genuine muffler cutter | MDJ8A00 MDJ8A10 | ¥19,800 (¥ 18,000) | With AutoExe logo for mounting genuine stainless steel muffler | D | 0.1 h |
※ 1 To install it, it is necessary to cut off the upper surface of the front bumper.
※ 2 Cannot be installed on MT vehicles from DJ5FS-600001 and XD 5MT halogen lamp vehicles from DJ300001FS-499999 to 6.
※ 3 Cannot be installed on all 15MB grade vehicles, DJLFS i-ELOOP equipped vehicles, DJLFS-100001 to 699999 MT vehicles, and DJ3FS MT 13C grade side airbag-equipped vehicles.
※ 4 Cannot be installed separately.Premier tail muffler center dual (MDJ8Y50 / 8Y60) and rear under panel (MDJ2420) / or rear under spoiler (MDJ2410) must be installed at the same time.
※ 5 Cannot be installed on high compression gasoline engine vehicles from DJLFS-750001 ~ / DJLAS-250001 ~.
Brake
The first thing that is required of a brake is the ability to stop safely.And in order to enjoy running freely, controllability that can decelerate at will is required.The brake pad, which has a small change in the coefficient of friction (μ) even during continuous braking, and the brace, which increases the rigidity of the pedal mounting part and eliminates the delay in effectiveness, realizes the effect of synchronizing with the driver's sensibility.>> Read more
■ Street sports brake pads
The aim is "deceleration at will".Designed with an emphasis on stable effectiveness during continuous braking, delicate load transfer in cornering, and flexible control of vehicle speed, rather than simply stopping performance.Focus on the amount of change and how to change the coefficient of friction (μ), which constantly changes depending on various conditions such as pedaling force, speed, and temperature.The "transient characteristics of μ" required by sports-oriented drivers realizes a taste that is synchronized with the sensibilities.>> More details
<Main specifications> ・ Non-asbestos friction material ・ Rotor proper temperature: 0 to 400 ℃
■ Club sports brake pads
Sometimes to the circuit ...A sports pad that aims for "deceleration at will" that synchronizes with the driver's sensibility in high load areas such as continuous corners and full braking from straight.The material is a blend of carbon and a metal material with excellent fade resistance.It balances the conflicting frictional force and the suppression of rotor aggression at a high level. >> More details
<Main specifications> ・ Graphite metal friction material ・ Rotor proper temperature: 50-800 ℃
■ Street brake rotor
Mass-produced XNUMX-piece structure with the same shape FC Cast iron, but with improved strength by controlling the content of carbon and silicon.Further heat treatment is applied to stabilize the metal connective tissue.It suppresses distortion due to heat and improves fade resistance and crack resistance.>> More details
<Main specifications> ・ 6 slits on one side ・ 1 piece type
■ Brake pedal brace
The bracket of the pedal mounting part, which causes slight distortion during brake operation, is three-dimensionally reinforced with steel braces to ensure rigidity.It improves the delay in reaction from when the pedal is pressed until the brake is applied, and contributes to a direct effect.>> More details
<Main specifications> -Steel 2-piece structure
Product name | 適合 車 種 (Model list) | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Street sports brake pads | front | All cars | MDJ5A10 | ¥16,500 (¥ 15,000) | Non-asbestos rotor Appropriate temperature: 0-400 ℃ | D | 0.5 h |
Club sports brake pads | front | All cars | MDJ5B10 | ¥25,300 (¥ 23,000) | Graphite metal rotor Appropriate temperature: 50-800 ℃ | D | 0.5 h |
Street brake rotor | front | DJ system (excluding DJ3FS) DJ3FS | MDJ5A50 MDJ5A51 | ¥41,800 (¥ 38,000) | 1 piece type with cleaning slit Left and right 2 pieces set | D | 1.0 h |
Brake pedal brace | All cars | MDJ4950 | ¥19,800 (¥ 18,000) | Steel 2-piece configuration | D | 0.6 h |
Engine & Drivetrain
A group of parts that draws out the full potential of the engine and converts it into traction.A sports clutch set and flywheel that support a pleasant gear change.Limited slip differential, which allows you to actively enjoy the change in the posture of the car when cornering, has created transient characteristics that eliminate sudden movements as much as possible while enhancing the direct feeling with the car.
■ Sports oil filter
Fine sludge is removed by using a high-efficiency filter medium.By expanding the filtration area by about 5% compared to mass production, filtration efficiency is improved and pressure loss is reduced.Furthermore, by incorporating a powerful neodymium magnet, metal wear debris is captured without missing.It balances the functions required for oil filters at a high level.Dedicated to gasoline engine vehicles. >> More details
<Main specifications> ・ Built-in strong magnet ・ Filtration area expanded by about 5% compared to mass production
■ Sports clutch line
Uses stainless mesh PTFE (Teflon), which has less deterioration due to heat and aging and less expansion due to hydraulic pressure than the rubber used in mass-produced vehicles.Contributes to a direct clutch feel.In addition, PVC coating is applied to protect the hose for safety. >> More details
<Main specifications> -Stainless steel mesh PTFE + PVC coating
■ Turbo pipe
By optimizing the layout of the turbo pipe that guides the air supercharged by the turbine to the intercooler, and combining the aluminum elbow pipe whose inner wall is mirrored as much as possible and the 4-layer polyster silicon that has a high deformation suppressing effect, the hose expands due to pressurization. And suppresses the resistance of the air flow path.As a result, the boost pressure rises faster and turbo lag is reduced.Improve the response from the beginning of stepping on the accelerator.The product comes with a gasket required for installation. >> More details
<Main specifications> -Aluminum pipe (anodized) + silicon hose / band / gasket included
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time |
---|---|---|---|---|---|---|
Sports oil filter | Gasoline car | A00182 | ¥3,080 (¥ 2,800) | Built-in strong magnet Filtration area expanded by about 5% compared to mass production | D | 0.1 h |
Sports clutch line | MT car | MDJ6500 | ¥11,000 (¥ 10,000) | Stainless mesh PTFE hose + PVC coating | D | 0.5 h |
Turbo pipe | Diesel Car | MDJ3960A | ¥46,200 (¥ 42,000) | Aluminum pipe (anodized finish) Silicon hose / band / gasket included | D | 0.8 h |
Utility
In order to enjoy everyday driving, I want to pay attention not only to running but also to the texture and usability of the appearance.Please also pay attention to utility items with functionality not found in mass-produced cars, such as a side visor with a ventilation mechanism that tightens the style with a sporty aero form.
■ Oil filler cap
The oil filler cap has been changed from genuine resin to 52S aluminum, which is fully machined and full of craftsmanship.Brilliant red alumite processing is applied to give a mechanical and gorgeous accent to the engine room.The laser-engraved AutoExe logo is also a delicate impression. >> More details
<Main specifications> ・ 52S aluminum fully machined ・ Red alumite processing ・ Laser engraved with AutoExe logo
■ Oil level gauge grip
An item that replaces the resin grip of a mass-produced oil level gauge with aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.DIY installation is possible with the attached dedicated tool. Compatible with a wide range of vehicles equipped with the SKYACTIV engine. >> More details
<Main specifications> -Aluminum-Red alumite-With AutoExe logo-Includes a dedicated tool for mounting
■ Brake fluid cap
The resin mass-produced brake fluid tank cap has been upgraded to aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.Combined with an oil filler cap and level gauge grip with the same design, it accelerates the total coordination of the engine room. >> More details
<Main specifications> -Aluminum-Fully machined-Red alumite processing-Laser engraved AutoExe logo included
■ Fuel cap cover
An ABS cover that can be attached over a mass-produced fuel cap.The design with cap bolts on bright Exe Red gives a gorgeous impression to the fuel filler port. With AutoExe logo.Compatible with a wide range of current Mazda vehicles. >> More details
<Main specifications> ・ ABS red painted ・ With decorative cap bolt ・ With AutoExe logo ・ Double-sided tape attached ・ Fuel label / erroneous oil supply prevention reminder sticker included
■ Fuel lid cover
Designed exclusively for vehicle models to be installed in mass-produced fuel lids.The product is made of ABS with a three-dimensional chrome-plated finish, and can be easily attached with double-sided tape.Gives a sporty and mechanical impression without breaking the character line of the vehicle.In addition, by combining it with the "fuel cap cover" that is attached to the separately sold mass-produced fuel cap, it is possible to enjoy a unified coordination around the fuel filler port. >> More details
<Main specifications> ・ ABS ・ Chrome plating ・ AutoExe logo included ・ Double-sided tape adhesive
■ Optima Battery
Synonymous with maintenance-free batteries, which boast a longer life than conventional open-type batteries.It is a completely sealed type that uses the original spiral cell technology, so there is no need to replenish the battery fluid.Provides a stable current even under high load.Can be installed without using additional adapters.>> More details
<Main specifications> -Maintenance-free type made by Optima Battery
■ Battery clamp
Playful in the engine room. Made of one-piece steel designed with the image of an AutoExe strut tower bar.The bright red color and logo plate have been faithfully reproduced.>> More details
<Main specifications> -Steel red paint-With AutoExe ornament
■ Aero sports wiper blade
An aero type wiper blade is used for the main body.By adding a deflector with fins, the arm joint is aero-formed.The wind pressure generated during driving is positively received and the wiper lift is suppressed.The blade rubber is evenly adhered to the glass surface to improve visibility when driving at high speeds in the rain. >> More details
<Main specifications> ・ Driver side: 550mm ・ Passenger seat side: 430mm ・ Twin rail type
■ Bonnet damper
The high-pressure gas damper assists light and smooth opening and closing.Since the existing lock stay is no longer required, the maintainability of the engine room is greatly improved.Bolt-on mounting is possible with a dedicated mount bracket that minimizes the load on the bonnet and frame of the mounting part.No drilling is required.>> More details
<Main specifications> ・ High-pressure filled gas damper ・ Dedicated bracket included
■ Sports side visor
A high-performance side visor with a ventilation mechanism in addition to rain and sun protection.When the recommended side window is open, the negative pressure generated during driving is used to actively discharge the indoor air.At the same time, it also has the effect of preventing the ingress of rainwater.>> More details
<Main specifications> -Smoke type acrylic resin-Set of 4 left and right with AutoExe logo
■ Door handle cover & protector set
A carbon-like matte design that protects the fragile door handle and gives it a sporty look.Pursuing high-quality details and achieving a natural and unified fitting.A package for one unit is available, and the door handle and protector can be purchased separately. >> More details
<Main specifications> ・ Carbon tone ・ Weather resistant ABS cover x 4 ・ PVC protector x 4 ・ One set
■antenna garnish
A dress-up item that makes the mass-produced shark fin antenna look fearless with its mechanical carbon pattern and AutoExe logo. The material is flexible PVC, and double-sided tape can be easily attached to the antenna body. *The antenna body is not included in the product.>> More details
<Main specifications> ・Carbon tone ・AutoExe logo included ・Made of PVC with double-sided tape ・Set of 2 left and right
■Wheel nut set
Irregular heptagonal (heptagonal) small diameter type with an aluminum end cap with the AutoExe logo.The main body is made of high-strength black-painted chrome vanadium steel that does not easily loosen at high temperatures.The knurled red-colored aluminum end cap adds a subtle and sophisticated accent to your car's footwell.>> More details
<Main specifications> - Body: Made of chrome vanadium steel, black paint - Cap: Made of aluminum, red anodized + clear paint - AutoExe logo included - Irregular heptagon type, special adapter wrench included
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time |
---|---|---|---|---|---|---|
Oil filler cap | All cars | A1400-03 | ¥6,380 (¥ 5,800) | One-touch type Aluminum red alumite with AutoExe logo | D | 0.1 h |
Oil level gauge grip | All cars | A1450-03 | ¥6,380 (¥ 5,800) | Aluminum red alumite with AutoExe logo Dedicated tool for mounting included | D | 0.2 h |
Brake fluid cap | All cars | A1900-03 | ¥7,480 (¥ 6,800) | Aluminum red alumite with AutoExe logo | D | 0.1 h |
Fuel cap cover | All cars | A1600-03A | ¥5,280 (¥ 4,800) | ABS red painted decorative cap with bolt AutoExe logo | D | 0.1 h |
Fuel lid cover | All cars | DJA1 V3 020 | ¥11,000 (¥ 10,000) | ABS chrome plated AutoExe logo double-sided tape adhesive | D | 0.3 h |
Optima battery | All cars | A01200 | ¥62,920 (¥ 57,200) | Color: Yellow Top | F | 0.3 h |
Battery clamp | All cars | A1700 | ¥7,480 (¥ 6,800) | Steel red paint with AutoExe logo | D | 0.1 h |
Aero sports wiper blade | All cars | MDJ0250 | ¥9,680 (¥ 8,800) | Equipped with a large wind deflector Water repellent glass compatible Front left and right set of 2 | D | 0.1 h |
Bonnet damper | All cars | MDJ2960 | ¥27,500 (¥ 25,000) | High-pressure gas-filled damper + dedicated mounting bracket Set of 2 left and right | D | 1.0 h |
Sports side visor | All cars | DJA1 V3 700 | ¥18,700 (¥ 17,000) | Smoke acrylic resin 4 piece set with ventilation mechanism | D | 0.5 h |
Door handle cover & protector set | All cars | KFA1 V3 110 | ¥29,260 (¥ 26,600) | Carbon-like weatherproof ABS cover x 4 PVC protector x 4 XNUMX set | D | 1.0 h |
antenna garnish | Vehicle equipped with shark type antenna ※ 1 | DJA1 V3 040 | ¥8,800 (¥ 8,000) | Carbon-like PVC with AutoExe logo, double-sided tape attached, left and right set of 2 | D | 0.3 h |
Wheel nut set | All cars | C9A1 V9 770 | ¥16,280 (¥ 14,800) | Includes a dedicated adapter wrench for mounting the Heptagon type with the AutoExe logo | D | 0.3 h |
※ 1 Sensitivity may decrease depending on the reception conditions when listening to the radio.
Interior parts
In order to clearly convey the driver's intention to drive to the car, I would like to pay close attention to the texture and functionality of the cockpit interface.For the interior, we have prepared an airbag-compatible steering wheel that has a casual and sporty sensibility and a shift knob that pursues a stroke feeling during operation.I want you to enjoy the dialogue with the car.
■ Sports steering wheel (nappa leather)
A red-colored center mark with a flat bottom shape ... An airbag-compatible product that uses high-quality nappa leather as the material for outstanding sportiness.The elliptical cross-section grip with dimple processing that is not too thick and easy to grip, and the dimple-processed leather and thumb grip that improve holdability are created with details to actively enjoy driving.>> More details
<Main specifications> -Made of nappa leather-SRS airbag system / steering switch compatible-Flat bottom shape
■ Sports steering wheel (genuine leather)
Sporty flat bottom shape.Specifications that are particular about details such as an oval cross-section grip that is easy to grip and a thumb grip that suppresses slippage.Emphasis is placed on operability and visibility, and the diameter is 370 mm, which is the same as that of mass-produced vehicles.>> More details
<Main specifications> -Flat bottom with a diameter of 370 mm-Red stitch-Compatible with genuine airbags / steering switches-Trade-in type
■ Carbon paddle shift lever
Made of high-quality real carbon that is mounted over the mass-produced steering shift switch.Improved operability by moderately increasing the size.The cockpit is made sporty by clarifying the response in sports driving. >> More details
<Main specifications> ・ With AutoExe logo ・ Double-sided tape adhesive type ・ All 4 pieces configuration ・ Overall length 100mm (upper + 25mm lower + 10mm extension compared to mass production)
■ Shift knob (spherical shape / genuine leather)
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details
<Main specifications> -For AT cars (straight type) -Made of genuine leather-Weight: 130g
■ Shift knob (spherical shape / genuine leather)
Made of genuine leather with a diameter of 51 mm with an emphasis on operability.A shift knob that fits easily in the palm of your hand and can be gripped on either the top or the side.You can adjust the height according to your physique and taste.AutoExe logo on the top.>> More details
<Main specifications> -For MT vehicles-Made of genuine leather-Screw size MT vehicles: M10 x 1.25-Weight: 190g
■ Shift knob (genuine leather)
Small diameter size with a diameter of 42 mm.A shift knob that fits easily in the palm of your hand and can be gripped on either the top or the side.You can adjust the height according to your physique and taste.Two types of stitches, red stitch and black stitch, can be selected.AutoExe logo on the top. >> More details
<Main specifications> -For MT vehicles-Made of genuine leather-Screw size MT vehicles: M10 x 1.25-Weight: 190g
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Sports steering wheel (Nappa leather / red center mark) | Red stitch | DJ system * 1 * 2 | KFA1 V0 310 | ¥49,500 (¥ 45,000) | Flat bottom shape compatible with SRS airbag system / steering switch | D | 0.5 h |
Sports steering wheel (Genuine Leather) | Red stitch | DJ system ※ 3 | MBM1370-03 | ¥41,800 (¥ 38,000) | Genuine SRS airbag system / steering switch compatible flat bottom shape | D | 0.5 h |
Carbon paddle shift lever | Vehicles equipped with steering shift switch | A1382-20 | ¥16,280 (¥ 14,800) | Carbon 4-piece construction with AutoExe logo | D | 0.1 h | |
Shift knob (Spherical shape / genuine leather) | Red stitch | AT car MT car | A1350B-03 A1341-03 | ¥19,580 (¥ 17,800) ¥9,900 (¥ 9,000) | Diameter: 51mm Overall length: 85mm Weight: 130g Push type Screw diameter: M10 x 1.25 Diameter: 51mm Overall length: 70-88mm Adjustable weight: 190g | D D | 0.2 h 0.1 h |
Shift knob (genuine leather) | Red stitch Black stitch | MT car MT car | A1396-03 A1396-08 | ¥9,680 (¥ 8,800) | Screw diameter: M10 x 1.25 Diameter: 42mm Overall length: 73-91mm Adjustable weight: 190g | D | 0.1 h |
※ 1 For DJ5FS / DJ5AS / DJLFS / DJ3FS / DJ3AS-300001 ~, DJLAS-100001 ~.
※ 2 The steering heater is not equipped and will not work.
※ 3 For DJ5FS / DJ5AS / DJLFS / DJ3FS / DJ3AS ~ -299999.
Goods
Real carbon and suede-like accessories that stand out sporty.Stickers and ornaments that decorate your styling.Please enjoy the coordination with your car in every detail with your sense.
■ Carbon number frame
Autoclave molded dry carbon license plate frame with dramatically improved material and design.UV cut clear coat finish that suppresses deterioration due to ultraviolet rays.A stainless steel AutoExe logo plate is placed in the center. >> More details
<Main specifications> -Autoclave molded dry carbon-UV cut clear coating finish-Stainless steel AutoExe logo plate included
■carbon number bolt
High quality number bolt set using dry carbon for the plate part. Dress up your license plate smartly with the 3-piece configuration of our unique low-head stainless steel bolt/carbon washer.>> More details
<Main specifications> - Made of CFRP (logo plate part: dry carbon) - UV cut clear coating finish - Stainless steel low head bolt - AutoExe logo included - Set of 1 for 3 car
■ Leather key holder
Just fit to the new advanced key.The outer skin is made of black cordovan, which has excellent durability.Soft red cowhide leather is used on the inside to gently wrap the smart key.Handmade specifications jointly planned with the pioneering system notebook brand "ASHFORD". >> More details
<Main specifications> Cordovan (horse leather) Made of cowhide AutoExe/ASHFORD embossed logo
■ Fragment case
Old and new advanced keys/card type keys can be stored.Based on black cordovan, which has excellent durability, perforated leather with red permeation expresses a sporty feeling.With card storage case + key chain.Handmade specifications jointly planned with the pioneering system notebook brand "ASHFORD". >> More details
<Main specifications> Cordovan (horse leather), cow leather, AutoExe/ASHFORD embossed logo
■ Carbon key cover
Dedicated to the new advanced key.Autoclave manufacturing method used for racing car bodies, etc. Made of dry carbon.The texture that makes the most of the texture of the material is attractive. >> More details
<Main specifications> -Made of dry carbon-With AutoExe logo-2-piece configuration-Double-sided tape adhesive type
■ Key case
A high-quality black suede-like key case compatible with conventional advanced keys.A cover type that firmly protects the key body from scratches and impacts.Red stitching and red lines give a sporty and delicate impression. >> More details
<Main specifications> ・ Black suede tone ・ Red stitch ・ With AutoExe logo
■ Car verification case
High-quality black suede-like that smartly stores in-vehicle documents such as vehicle verification, instruction manuals, and maintenance notes.The red stitching, which is unified to the liner inside the case, also enhances the sports mind. >> More details
<Main specifications> -Black suede tone-Red stitch-AutoExe embossed logo-Size: 245 x 180 x 65 mm
■ Ornaments / stickers
You can enjoy it with your own taste.It is also good to dress up with the demo car as a model.
A lineup of high-quality AutoExe logo decorations that make you feel the commitment to driving. >> More details
Product name | 適合 車 種 | part number | Tax-included price (Price without tax) | Spec. | Codes | Reference work time | |
---|---|---|---|---|---|---|---|
Carbon number frame * 1 * 2 | For front license plate mounting | A1800-20 | ¥18,480 (¥ 16,800) | Made of CFRP (dry carbon) UV cut clear coating finish Comes with stainless steel AutoExe logo plate | D | 0.1 h | |
carbon number bolt | General-purpose products (excluding character light type license plates) | C9A1 V9 760 | ¥9,350 (¥ 8,500) | Made of CFRP (logo plate part: dry carbon) UV cut clear coating finish Stainless steel low head bolts with AutoExe logo Set of 1 for 3 car | D | 0.1 h | |
leather key holder | Vehicles equipped with the new advanced key ※ 3 | MAA0005 | ¥19,800 (¥ 18,000) | Made of cordovan (horse leather) and cowhide with AutoExe/ASHFORD embossed logo | F | - | |
fragment case | General-purpose products | MAA0006 | ¥14,850 (¥ 13,500) | Made of cordovan (horse leather) and cowhide with AutoExe/ASHFORD embossed logo Size: 150mm x 72mm x thickness 5-15mm | F | - | |
Carbon key cover | Vehicles equipped with the new advanced key ※ 3 | A2650-20 | ¥10,780 (¥ 9,800) | Made of CFRP (dry carbon) with AutoExe logo, 2-piece construction, double-sided tape adhesive type | D | - | |
key case | Vehicles equipped with advanced keys | A2640-33 | ¥4,180 (¥ 3,800) | Black suede-like red stitching with AutoExe logo.Size: 95mm x 45mm x 20mm | D | - | |
Car verification case | General-purpose products | A2810-33A | ¥7,480 (¥ 6,800) | Black suede-like red stitch with AutoExe logo Size: 245 x 180 x 65 mm | D | - | |
Bright ornament | General-purpose products | A12500 | ¥5,280 (¥ 4,800) | Chrome-plated ABS resin double-sided tape adhesive type Size 155mm x 20mm | D | - | |
ornament | General-purpose products | A12000 | ¥1,980 (¥ 1,800) | Aluminum double-sided tape adhesive type Size 120mm x 24mm | B | - | |
Wind logo sticker | General-purpose products | black | A10000-08 | sold out. | One-touch transfer type Size 235mm x 48mm | B | - |
Message logo sticker | General-purpose products | A11900-03 | ¥880 (¥ 800) | One-touch transfer type Size 158mm x 28mm | B | - | |
Logo sticker (L) | General-purpose products | silver Red white | A11200-02 A11200-03 A11200-04 | ¥1,320 (¥ 1,200) | Character type without characters Size 550mm x 56mm | B | - |
Logo sticker (S) | General-purpose products | silver Red white | A11300-02 A11300-03 A11300-04 | ¥660 (¥ 600) | Character type without characters Size 270mm x 28mm | B | - |
※ 1 This product may appear on a part of the in-vehicle monitor screen such as a car equipped with a front camera.
※ 2 Cannot be installed on vehicles equipped with the MAZDA 2 360 ° view monitor.
※ 3 The leather key holder (MAA0005) and carbon key cover (A2650-20) cannot be installed at the same time.
MAZDA2 / Demio Parts impression
We are posting the raw voice of the customer who is actually wearing it.
Please refer to the car personalization project.