Front under spoiler

Accented with an air duct motif. The dynamic form, which incorporates a high nose and forward-swept wing tips, adds graceful strength. Painted piano black.

trunk spoiler

The combination of real carbon and piano black quietly asserts a sports mindset. A simple appearance that expresses the flow of mass-produced trunks.

Rear side cowl

The duct motif boldly depicts the flow of air. Gives a sporty accent. (Snowflake White Mica/Soul Red Crystal M/Machine Gray Premium M pre-painted products are available)

Door mirror cover

The carbon-like matte finish with a subtle fin design makes the body look fearless. Includes AutoExe logo sticker. Double-sided tape attached.

Sports muffler (dual)

Two left and right output specifications that can be installed at the same time as the muffler garnish. The straight structure silencer produces a gentle and unsatisfactory sound.

Muffler garnish

A dedicated garnish that can be installed at the same time as the sports muffler. A mass-produced bumper is cut and installed to create a rear view with a sense of unity.

carbon seat back bar bezel 　

Made of dry carbon used in racing cars, etc. Along with the prominent AutoExe three-dimensional logo, it appeals to following vehicles with its authentic appearance.

Fuel lid cover

A mechanical one-point item that gives off a metallic feel.Double-sided tape is attached to the mass-produced fuel lid cover.

Door handle cover & protector set

A matte carbon finish that protects the paint on the door handle and gives the styling a sporty look.

ND-05S

ND-05

■ Lowdown spring
The styling is sporty and tightened in combination with a mass-produced damper, and the handling is improved by lowering the center of gravity.By suppressing the vehicle height to -20 mm and the spring constant to about 120%, the suspension stroke is secured and comfort is also taken into consideration.　>> More details

<Main specifications> ・ Vehicle height: -20mm ・ Spring constant is here.Please refer to

■ Sports damper
Although it has the same shape as the mass-produced product, the internal piston adopts a "very low speed valve" that generates precise damping force from the moment it starts moving.It accurately controls changes in the vehicle's posture and achieves a sporty, flat and high-quality ride.It is recommended to use with genuine springs (can be used with lowdown springs).>> More details

<Main specifications> ・ Fixed gas damping force

■ Street Sports Suspension Kit (KIJIMA-SPEC)
A height-adjustable kit that aims for normal evolution to enjoy driving while maintaining the balance of mass production specifications.Based on the dynamic Kansei engineering theory of Mr. Takao Kijima, who was the development chief of sports cars as an authority on suspension during his tenure at Mazda Motor Corporation, the vehicle height, spring constant, and damper damping force are set.It is tuned to exquisite handling that exceeds the restrictions of mass-produced cars.Uses a high-precision twin tube damper and a dedicated trapezoidal spring with excellent lateral rigidity. >> More details

<Main specifications> ・ Twin tube full length adjustable vehicle height ・ Fixed damping force type ・ Recommended vehicle height -15mm

■ Club Sports Suspension Kit
A model exclusively for FR sports cars that has reduced comfort to the limit that we can tolerate and converted the margin into athletic performance.The standard vehicle height is -30mm.In order to maintain accurate operability even in winding and hard circuit driving, a monotube type damper with excellent heat conversion ability at high load and a series-wound spring with a spring constant that rises linearly are adopted.Creates a solid driving sensation with a high sense of change regardless of the speed range. >> More details

<Main specifications> ・ Monotube full length adjustment type ・ Damping force 24 steps adjustment type ・ Recommended vehicle height -30mm ・ Spring constant: Fr: 68.6 Rr: 39.2N / mm

■ Adjustable stabilizer link
When the vehicle height is down, the angle of the lower arm changes.As a result, the arm angle between the stabilizer and the link becomes an acute angle, which tends to spoil the original stabilizer effect.This product corrects the arm angle when the vehicle height is lowered by adjusting the link length.Optimize the stabilizer function.>> More details

<Main specifications> -Full length adjustable XNUMX-piece set-For front-Axial mount type

■ Sports stabilizer
A stabilizer that connects the left and right suspension arms with a pipe and suppresses roll by the spring effect.From mass production, the spring constant has been strengthened by 140% at the front and 275% at the rear.Stabilizes the posture when cornering while keeping controllability.Since the spring effect hardly occurs when going straight, the effect on the ride quality is minimal. >> More details

<Main specifications> ・ Front: Solid φ23.0 with dedicated rubber mount Spring constant 140% ・ Rear: Hollow φ14.0 Dedicated mount rubber / bracket included Spring constant 275%

■ Sports tie rod end
The tie rod that connects the steering and the left and right knuckles of the front wheels is designed based on the genuine vehicle height.Therefore, the angle of the tie rod changes when the vehicle height is lowered, which induces a toe change during cornering.This product is an item that restores the original steering characteristics by correcting the tie rod angle during lowdown. >> More details

<Main specifications> -Carbon steel (S45C / forged) -Set of 2 left and right

■ Upper mount bush set
Mass-produced shape product with 127% higher rubber hardness.A set of 8 for one unit to be attached to the top mount of the damper.It suppresses the bending of the rubber from the moment the damper starts to move, and supports the quick rise of damping force.It is recommended to replace the suspension at the same time. >> More details

■ Suspension bush set (upper)
Mass-produced shape product with rubber hardness increased by 125 to 146%.A total of 8 locations, including front and rear upper arms and lateral / leading links, are set.While ensuring practicality, it suppresses the bending of rubber in moving parts and supports accurate handling.It is also possible to purchase a single item for each part.>> More details

■ Suspension bush set (lower)
Mass-produced shape product with rubber hardness increased by 109-140%.Eight front lower arms, rear trailing / toe control / lateral link, and 8 rear axles are set.While ensuring practicality, it suppresses the bending of rubber in moving parts and supports accurate handling.It is also possible to purchase a single item for each part. >> More details

■ Strut tower bar
Adopted a one-piece structure in which a steel oval shaft, which is advantageous in terms of rigidity, is integrally molded by welding.The left and right struts are connected via the bulkhead to improve body rigidity.It is effective when installed separately, but it is best to use it in combination with a floor crossbar that is set separately. >> More details

<Main specifications> -Steel oval shaft 4-piece structure XNUMX-point type

■ Floor crossbar
With a simple structure that allows one bar to crawl in the left-right direction of the floor, it demonstrates the tower bar effect.Since it also serves as a suspension mounting point with high strength, the burden on the body is extremely small.There is almost no impact on the utility space.It is effective when used alone, but it is recommended to install it together with the strut tower bar. >> More details

<Main specifications> -Steel oval shaft 2-piece structure 4-point type

■ Tower brace set
The aim is to obtain a thin and rigid feeling in the closed body.While following the basic layout of the existing strut tower bar / floor crossbar, the specifications are such that the rigidity of the brace body is increased as much as possible.Since the degree of rigidity increase is high, it is best to set only the front and rear sets, and to install it at the same time as the member brace set that solidifies the underfloor on the surface. >> More details

<Main specifications> ・ Steel oval shaft front and rear 4-piece configuration ・ Weight: 8.0kg

■ Member brace set
A structure developed from the crossbar equipped for mass production.By mounting a frame with a three-dimensional truss structure on the entire underfloor, the chassis rigidity of the highest level as a bolt-on part is obtained.In combination with the tower bar / floor cross bar that reinforces the front and back of the upper part of the body, a tough monocoque body with two upper and lower stages is completed. >> More details

<Main specifications> -Steel oval shaft front and rear 3-piece structure-Weight: 7.5 kg

■ Motion control beam
Reinforces the front and rear ends of the body to increase torsional rigidity.By suppressing the vibration of the body due to high rigidity with a friction type damper with ultra-high damping, it creates a street best ride with strength and suppleness.A set of two front and back.With a dedicated mounting bracket.>> More details

<Main specifications> -Friction type damper + steel shaft Front and rear set with mounting bracket

■ Air filter replacement
Utilizing the air cleaner case of mass-produced cars, replacing only the filter part effectively improves the accelerator response.The dry filter, which has a good balance between ventilation performance and dust collection effect, is a disposable type that has little effect on the air flow sensor and is easy to maintain.　>> More details

<Main specifications> ・ Dry type ・ Disposable (disposable) type

■ Sports induction box
By utilizing the air cleaner box of a mass-produced vehicle, the intake side case is replaced. Fresh air is directly guided to the air filter, improving intake efficiency. The sound also becomes sporty. Combining it with the optional air filter replacement increases efficiency even further.　>> More details

<Main specifications> -Funnel type FRP frame + aluminum heat shield

■ Ram air intake system
High efficiency while following the basic layout of mass production.The intake duct equipped with a large air guide inside the front grill directly captures the fresh running wind that is not affected by the radiant heat of the radiator and exerts a ram pressure effect.By combining a carbon cleaner box with a straightened suction path and a large capacity as much as possible and a conical filter with high suction efficiency, the filling efficiency is improved in response to the increased suction amount. >> More details

<Main specifications>・Special wet filter + carbon duct

■ Intake suction kit
Specifications that secure the maximum effective flow path area of ​​intake air and reduce intake resistance.The material used is multi-layer polystar silicon, which has a high effect of suppressing deformation due to negative suction pressure.As a result, the accelerator response has been improved.The crimson coloring adds an accent to the engine room.　>> More details

<Main specifications> ・ Made of 4-layer polystar silicon

■ Premier tail muffler
A series with a sophisticated and profound feeling. The 110x95mm oval-shaped tail end has a very mature feel.With a large-capacity straight structure silencer that has been carefully tuned for a narrow main pipe diameter and internal structure, it achieves both improved accelerator response from the practical range and a gentle sports sound that suppresses the noise inside the room.　>> More details

<Main specifications> ・ Stainless steel ・ Straight structure silencer ・ Main diameter: Φ60.5 ・ Tail diameter: Φ110 × 95

[Sound library for audition] * You can compare it with the mass-produced muffler recorded under the same conditions.It may not be accurate due to the characteristics of the playback environment, but please watch it as a reference for changes in sound quality and volume.

■ Sports muffler (single)
Adopted a 90mm diameter slash tail with a sub-silencer, which is suitable for the name of sports.In terms of functionality, improving exhaust efficiency has been given top priority, and the multi-stage expansion type of mass-produced vehicles has been changed to a straight structure to reduce back pressure loss.Examining the pipe diameter and length, etc., to obtain an agile response.For muffling, a method is adopted in which the propagation distance of the sound wave is created and the phase is shifted so that the high and low frequencies of the sound interfere with each other.It creates a sport sound without any miscellaneous taste. >>Click for details

[Sound library for audition] * You can compare it with the mass-produced muffler recorded under the same conditions.It may not be accurate due to the characteristics of the playback environment, but please watch it as a reference for changes in sound quality and volume.

■Sports muffler (dual)
Two left and right output specifications with a slash tail with a diameter of 76 mm. Attach at the same time as the muffler garnish. In terms of functionality, we prioritized improving exhaust efficiency, changing from the multi-stage expansion type of mass-produced vehicles to a straight structure to reduce back pressure loss. We carefully examine the pipe diameter and length to achieve quick response. For noise reduction, we use a method that creates a propagation distance for sound waves and shifts the phase to interfere with the high and low frequencies of the sound. It creates a sports sound without any frills. >> More details

[Sound library for audition] * You can compare it with the mass-produced muffler recorded under the same conditions.It may not be accurate due to the characteristics of the playback environment, but please watch it as a reference for changes in sound quality and volume.

■Muffler garnish (for sports muffler dual installation)
A dedicated garnish that can be installed at the same time as the sports muffler. A mass-produced bumper is cut and installed to create a rear view with a sense of unity. Made by AES, black matte finish (no painting required), cannot be installed separately.

<Main specifications> - For vehicles equipped with sports muffler (dual) - Cannot be installed separately - Made by AES - Black matte finish (painting not required) - Rear bumper removal required

■ Sports muffler (center dual)
"Sports muffler" has evolved the muffling method from "sound absorption to interference" and contributes to the improvement of engine output in the entire range in terms of performance.Since no sound absorbing material is used, theoretically there is no increase in volume over time.You can enjoy a clear exhaust note with restraint for a long time.In terms of visuals, the combination of the new design dual tail with a perfect circle of φ90 x 2 and the rear under panel completes a compact rear view that is typical of lightweight sports.Cannot be installed separately.Must be installed at the same time as the rear under panel. >> More details

[Sound library for audition] * You can compare it with the mass-produced muffler recorded under the same conditions.It may not be accurate due to the characteristics of the playback environment, but please watch it as a reference for changes in sound quality and volume.

■Rear under panel (sports muffler Center dualfor mounting)
At the same time as covering the notch at the outlet of the mass-produced muffler, by combining it with a sports muffler, it realizes a tight form that is typical of lightweight sports.Piano black painted product.Cannot be installed separately.Must be installed at the same time as the sports muffler.

<Main specifications> -Piano black painted-ABS resin-Cannot be installed separately It is necessary to install it with a sports muffler (center dual) at the same time.

■ Street sports brake pads
The aim is "deceleration at will".Designed with an emphasis on stable effectiveness during continuous braking, delicate load transfer in cornering, and flexible control of vehicle speed, rather than simply stopping performance.Focus on the amount of change and how to change the coefficient of friction (μ), which constantly changes depending on various conditions such as pedaling force, speed, and temperature.The "transient characteristics of μ" required by sports-oriented drivers realizes a taste that is synchronized with the sensibilities.　>> More details

<Main specifications> ・ Non-asbestos friction material ・ Rotor proper temperature: 0 to 400 ℃

■ Club sports brake pads
Sometimes to the circuit ...A sports pad that aims for "deceleration at will" that synchronizes with the driver's sensibility in high load areas such as continuous corners and full braking from straight.The material is a blend of carbon and a metal material with excellent fade resistance.It balances the conflicting frictional force and the suppression of rotor aggression at a high level.　>> More details

<Main specifications> ・ Graphite metal friction material ・ Rotor proper temperature: 50-800 ℃

■ Sports brake rotor
Two-piece structure with improved strength such as fade resistance and crack resistance.Specifications that pursue functions such as ventilation fins with excellent heat dissipation and cleaning slits that prepare the pad surface.The lightweight duralumin bell housing can also be expected to improve handling.When it is exhausted, only the disc rotor can be replaced. >> More details

<Main specifications> ・ 8 slits on one side, 2 piece type

■ Street brake rotor
Mass-produced XNUMX-piece structure with the same shape FC Cast iron, but with improved strength by controlling the content of carbon and silicon.Further heat treatment is applied to stabilize the metal connective tissue.It suppresses distortion due to heat and improves fade resistance and crack resistance. >> More details

<Main specifications> ・ 6 slits on one side, 1 piece type

■Master back brace
Focus on the rigidity of the unit from the brake pedal that converts pedaling force to hydraulic pressure to the master cylinder.The pedal mounting part, bulkhead / master back, and body on the engine room side are three-dimensionally reinforced with high-rigidity steel braces.By suppressing the distortion of the entire unit, the delay in reaction from when the pedal is pressed until the brake is applied is improved. Contribute to the realization of "deceleration at will".　>> More details

<Main specifications> -Steel 5-piece configuration

■ Sports oil filter
Fine sludge is removed by using a high-efficiency filter medium.By expanding the filtration area by about 5% compared to mass production, filtration efficiency is improved and pressure loss is reduced.Furthermore, by incorporating a powerful neodymium magnet, metal wear debris is captured without missing.It balances the functions required for oil filters at a high level.Dedicated to gasoline engine vehicles. >> More details

<Main specifications> ・ Built-in strong magnet ・ Filtration area expanded by about 5% compared to mass production

■ Sports clutch set
The facing material is a non-asbestos material that exhibits high mu in a wide temperature range.In combination with the Doug tile cast iron cover, which has a crimping force increased by about 30% compared to mass production, reliable torque transmission is possible.Although it requires some pedaling force for operation, it is a characteristic that is easy to handle in sports driving because the meet point at half-clutch is clear compared to mass production. >> More details

<Main specifications> -Mass production shape non-asbestos type

■ Sports flywheel
A specially designed product that moderately reduces the weight of mass-produced flywheels and reduces the moment of inertia by 28 to 37% each.The effect on operability is minimal, and it is possible to improve engine response.The decrease in durability, which is a concern due to weight reduction, is dealt with by using a fully machined chrome molybdenum steel material with excellent thermal stability.　>> More details

■ Sports clutch line
Uses stainless mesh PTFE (Teflon), which has less deterioration due to heat and aging and less expansion due to hydraulic pressure than the rubber used in mass-produced vehicles.Contributes to a direct clutch feel.In addition, PVC coating is applied to protect the hose for safety. >> More details

<Main specifications> -Stainless steel mesh PTFE + PVC coating

■ Quick shifter
Pursuing a sense of moderation by eliminating leaf springs and urethane bushes that alleviate shift shocks installed in mass-produced products.Approximately 24% shorter stroke by changing the lever ratio.Achieves a direct and quick operation feeling that is typical of a sports car that is neither too heavy nor too light. In combination with the AutoExe shift knob, the shift stroke can be adjusted to suit the driver's taste. >> More details

<Main specifications> ・ 24% shorter stroke than mass production

■ Limited slip differential.
The mechanical (multi-plate clutch) limited slip differential that distributes and transmits effective traction to the left and right drive wheels when cornering or on slippery roads is based on the proven CUSCO company and is based on the proven AutoExe. The original setting was applied.The operating method is 1.5 Way.Compared to mass-produced products, the direct operation feel is attractive.　>> More details

<Main specifications> -Mechanical 1.5way cam angle 35 °-Torque bias ratio: 4.0-6.0-Specified LSD oil is included.

■ Oil filler cap
The oil filler cap has been changed from genuine resin to 52S aluminum, which is fully machined and full of craftsmanship.Brilliant red alumite processing is applied to give a mechanical and gorgeous accent to the engine room.The laser-engraved AutoExe logo is also a delicate impression.　>> More details

<Main specifications> ・ 52S aluminum fully machined ・ Red alumite processing ・ Laser engraved with AutoExe logo

■ Oil level gauge grip
An item that replaces the resin grip of a mass-produced oil level gauge with aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.DIY installation is possible with the attached dedicated tool. Compatible with a wide range of vehicles equipped with the SKYACTIV engine.　>> More details

<Main specifications> -Aluminum-Red alumite-With AutoExe logo-Includes a dedicated tool for mounting

■ Brake fluid cap
The resin mass-produced brake fluid tank cap has been upgraded to aluminum, which is full of craftsmanship.Red alumite processing and laser engraved AutoExe logo give the engine room a mechanical and gorgeous accent.Combined with an oil filler cap and level gauge grip with the same design, it accelerates the total coordination of the engine room.　>> More details

<Main specifications> -Aluminum-Fully machined-Red alumite processing-Laser engraved AutoExe logo included

■ Fuel lid cover
Designed exclusively for vehicle models to be installed in mass-produced fuel lids.The product is made of ABS with a three-dimensional chrome-plated finish, and can be easily attached with double-sided tape.Gives a sporty and mechanical impression without breaking the character line of the vehicle.In addition, by combining it with the "fuel cap cover" that is attached to the separately sold mass-produced fuel cap, it is possible to enjoy a unified coordination around the fuel filler port.　>> More details

<Main specifications> -Made of ABS-Chrome plating-With AutoExe logo-Double-sided tape adhesion

■ Fuel cap cover
An ABS cover that can be attached over a mass-produced fuel cap.The design with cap bolts on bright Exe Red gives a gorgeous impression to the fuel filler port. With AutoExe logo.Compatible with a wide range of current Mazda vehicles.　>> More details

<Main specifications> ・ ABS red painted ・ With decorative cap bolt ・ With AutoExe logo ・ Double-sided tape attached ・ Fuel label / erroneous oil supply prevention reminder sticker included

■ Optima Battery
Synonymous with maintenance-free batteries, which boast a longer life than conventional open-type batteries.It is a completely sealed type that uses the original spiral cell technology, so there is no need to replenish the battery fluid.Provides a stable current even under high load.Can be installed without using additional adapters.>> More details

<Main specifications> -Maintenance-free type made by Optima Battery

■ Battery clamp
Playful in the engine room. Made of one-piece steel designed with the image of an AutoExe strut tower bar.The bright red color and logo plate have been faithfully reproduced.>> More details

<Main specifications> -Steel red paint-With AutoExe ornament

■ LED fog lamp kit
A roadster-specific design that can be mounted directly on the mass-produced front bumper.A 40-chip high-power LED is built into a compact 5 mm diameter lamp.Ensure visibility when driving in bad weather by irradiating with appropriate light.A smart installation is possible with an assembled package of control units, brackets, power harnesses, switches, etc.

<Main specifications> ・ Built-in 5-chip LED for mass production bumper installation ・ Diameter φ40 ・ With power harness / switch Luminous intensity: 4800cd (candela)

■ Aero sports wiper blade
An aero type wiper blade is used for the main body.By adding a deflector with fins, the arm joint is aero-formed.The wind pressure generated during driving is positively received and the wiper lift is suppressed.The blade rubber is evenly adhered to the glass surface to improve visibility when driving at high speeds in the rain. >> More details

<Main specifications> ・ Driver side: 450mm ・ Passenger seat side: 480mm ・ Twin rail type

■ Door handle cover & protector set
A carbon-like matte design that protects the fragile door handle and gives it a sporty look.Pursuing high-quality details and achieving a natural and unified fitting.A package for one unit is available, and the door handle and protector can be purchased separately. >> More details

<Main specifications> ・ Carbon tone ・ Weather resistant ABS cover x 2 ・ PVC protector x 2 ・ One set

■Door handle protector
Made of carbon-like PVC that protects the paint around the door handle, which is easily damaged when opening and closing. The lineup includes three colors: black, silver, and red (a color similar to Soul Red Crystal Metallic) that can be selected according to the body color.>>Click here for part numbers and prices

<Main specifications> - Carbon-like AutoExe logo included - PVC double-sided tape adhesive - Left and right set

■ Wheel nut set
Irregular heptagonal (heptagonal) small diameter type with an aluminum end cap with the AutoExe logo.The main body is made of high-strength black-painted chrome vanadium steel that does not easily loosen at high temperatures.The knurled red-colored aluminum end cap adds a subtle and sophisticated accent to your car's footwell.>> More details

<Main specifications> - Body: Made of chrome vanadium steel, black paint - Cap: Made of aluminum, red anodized + clear paint - AutoExe logo included - Irregular heptagon type, special adapter wrench included

■Air valve cap
Following the design of AutoExe wheel nuts, this product is made of aluminum with a red anodized finish, allowing you to enjoy a total coordination. The brass threads that are exposed on mass-produced plastic caps are covered to give a clean and sophisticated impression around the wheel.>> More details

<Main specifications> Aluminum, red anodized + clear coating with AutoExe logo (on both sides), set of 4

■ Helical short antenna
A short type with a total length of 105 mm with a built-in high-sensitivity helical coil inside the antenna.A roadster-specific design that realizes a fitting with a sense of unity. With AutoExe logo.>> More details

<Main specifications> ・ Built-in helical coil ・ Overall length: 105mm Screw diameter: M5 × 0.8mm ・ AutoExe logo included

We apologize for the inconvenience. We are currently receiving a large number of orders, and we plan to ship the product in early June 2025 (February 2025.2.20, XNUMX).

■ Full bucket seat TYPE-A7
It is a full bucket type that holds the driver firmly even under strong lateral G-forces. The basic shell is made of high-rigidity FRP. The side supports are asymmetrical to fit perfectly into the tight interior of the ND. The outer skin is a flame-retardant material with bold black and red or light gray stripes. It is packed with functions ideal for sports driving, such as belt holes for 35-XNUMX point seat belts, a height that allows the hip position to be lowered by up to XNUMX mm, and a back angle adjustment mechanism.　>> More details

<Main specifications> ・FRP ・Flame-retardant PVC skin ・Black/red stripe ・Seat cushion included ・AutoExe logo included ・Stripes and stitching: Red/light gray (2 colors available)

■ Sports steering wheel
Eye-catching center mark and flat bottom shape... This airbag compatible product is made of high-quality nappa leather, giving it a sporty look. It is designed with details to make driving more enjoyable, such as an oval cross-section grip with dimple processing that is not too thick and easy to hold, and dimpled leather and thumb grips that improve holding power.>> More details

<Main specifications> ・Made of genuine leather (nappa leather) ・Compatible with SRS airbag system/steering switch ・Flat bottom shape ・Stitching (center mark): Red/light gray (2 colors available)

■ Carbon paddle shift lever
Made of high-quality real carbon that is mounted over the mass-produced steering shift switch.Improved operability by moderately increasing the size.The cockpit is made sporty by clarifying the response in sports driving.　>> More details

<Main specifications> ・ With AutoExe logo ・ Double-sided tape adhesive type ・ All 4 pieces configuration ・ Overall length 100mm (upper + 25mm lower + 10mm extension compared to mass production)

■ Shift knob (ball shape) for MT
Made of genuine leather (nappa leather) with a diameter of 51 mm, with an emphasis on operability. The shift knob fits comfortably in the palm of your hand and can be held either sideways or upright. The height can be adjusted to suit your physique and preferences. The AutoExe logo is printed on the top.>> More details

<Main specifications> ・For manual transmission vehicles ・Made of genuine leather (nappa leather) ・Thread size: M10 x 1.25 ・Diameter: 51mm ・Total length: Adjustable from 70 to 88mm ・Stitching: Red/Black/Light Gray (3 colors available)

■ Shift knob (ball shape) for AT
Designed exclusively for straight AT vehicles, with a focus on the stroke feeling when the shift lock is released.The clean appearance and operability of mass-produced products without the unlock button are attractive.Push the upper end of the shift knob during operation.Shift the knob as it is.>> More details

<Main specifications> ・For automatic transmission vehicles (straight type) ・Made of genuine leather ・Diameter: 51mm ・Total length: 87mm ・Push type ・Red stitching

■ Shift knob (stick shape) for MT
Made of genuine leather (nappa leather) with a small diameter of 42 mm. The shift knob fits comfortably in the palm of your hand and can be held either sideways or upright. The height can be adjusted to suit your build and preferences. The AutoExe logo is printed on the top. >> More details

<Main specifications> ・For manual transmission vehicles ・Made of genuine leather (nappa leather) ・Screw size: manual transmission vehicles: M10 x 1.25 ・Diameter: 42mm ・Total length: adjustable from 73 to 91mm ・Stitching: red/black/light gray (3 colors available)

■carbon seat back bar bezel
Made of dry carbon used in racing cars, etc. Along with the prominent AutoExe three-dimensional logo, it appeals to following vehicles with its authentic appearance.■Cannot be installed on Roadster RF

<Main specifications> CFRP (dry carbon) AutoExe logo included Double-sided tape attachment Set of 2 (left and right)

■Center console lid
Soft pad specification designed exclusively for the ND. The console lid, where the driver places his elbow when shifting gears, is made of a soft-touch material, improving driving operability and comfort. The surface is synthetic leather with a texture similar to that of mass-produced shift boots and handbrake boots, and two part numbers are available with stitch colors that blend in with the interiors of the later model (light gray) and the earlier model (red). >> More details

<Main specifications> Made of ABS, flame-retardant PVC soft padding, surface color: Black, stitching: Gray/Red (2 colors available)　

■Wide rear view mirror
Frameless type compatible with conventional NDERC and ND5RC. The blue-coated mirror has a viewing area that is 1.7 to 1.8 times wider than mass-produced products. The radius of curvature is 3000SR to reduce parallax with the side mirror. Contributes to comfortable driving with less eye movement. The smart fitting that doesn't feel like an afterthought is appealing. Two types are available, compatible with vehicles equipped with auto-dimming mirrors and manual dimming mirrors.>> More details

<Main specifications> - Blue chrome surface mirror - Approximately 1.7 to 1.8 times the viewing area compared to mass production - Radius of curvature 3000SR AutoExe logo included - Anti-vibration cushion included

■ Knee pad set
Designed exclusively for ND.Firmly supports both knees and suppresses changes in the driver's posture during sports driving.Supports accurate pedal work.The skin has a flocky coating finish that feels good to the touch.It is a left and right set of the driver's door side and the console side of the three-step height adjustment type (can also be purchased separately).In addition, it is possible to complete the ideal holding environment for the whole body by combining with a different set full bucket seat Type-A3. 　>> More details

<Main specifications> FRP flocky coating (flocked paint) finish Door side (3-step height adjustment type) Left and right console side set AutoExe logo plate included

■ Sports floor mat
A high-quality floor mat set with an impressive red x black gradation that gives the interior a gorgeous color.The material is a soft wool-like fabric made from special chemical fibers in a loop weave.The driver's side is equipped with a large heel pad made of hard fiber that supports accurate pedal work during sports driving, achieving both texture and drivability. >> More details

<Main specifications> ・High-grade wool-like material ・Equipped with a large heel pad (driver's side) ・With aluminum AutoExe logo plate (front left and right) ・One set