As an authentic sports package, the DJ-06 frees your MAZDA2 for a dashing drive.


previous arrow
next arrow

The aim is to revive the sport. The real sports package.

The Mazda2 has evolved into a premium compact model. While maintaining this sense of beauty and quality, we devoted our efforts to enhancing the agile sportiness appropriate for a lightweight body, just like the sports grade “Sport” that used to exist in Demio.
The styling kit symbolizing this consists of 4 items: A front and rear under spoiler, front grille, and rear roof spoiler, all of which eliminate gaudiness. The blackout and virile outfit exude high quality athleticism.
The key issue for the drive quality is a motion control beam that has both increased torsional rigidity and a damping effect. The combination of several body reinforcement parts and a suspension that has been polished for the transient characteristics of the roll makes for sharp and accurate handling. In addition, the vehicle is equipped with exhaust and intake system tuning that is optimized for diesel and gasoline models. As an authentic sports package, the DJ-06 frees your MAZDA2 for a dashing drive.

Styling Kit

previous arrow
next arrow
previous arrownext arrow


■DJ-06 Styling Kit for MAZDA2(DJ)
DescriptionModelPart NumberPriceSpecificationCode
Front Under SpoilerAllMDJ2150-08¥82,000Fiberglass,Painted(Piano Black)D
Front GrilleAllMDJ2510¥78,000ABS,Painted(Piano Black/Mat Black)D
Rear Under PanelAllMDJ2430¥42,000AES,Unnecessary paintD
Rear Roof SpoilerAll



Fiberglass,Painted(Piano Black)



The simple yet boldly evolved front bumper and grille are also available with millimeter wave radar functions. The eye-catching Markless Grille and the horizontal blackout of the bumper duct give the vehicle a low visual center of gravity. Combined with the floating type rear roof spoiler it exudes institute heat without compromising the Demio’s stylishness.

Styling Kit

DJ-05S Styling Kit

previous arrow
next arrow
previous arrownext arrow



previous arrow
next arrow
previous arrownext arrow

■DJ-05S Styling Kit for Demio(DJ 2WD)
DescriptionModelPart NumberPriceSpecificationCode
Front Bumper&GrilleVIN-300001~




Rear Roof SpoilerAllMDJ2600¥40,000Fiberglass,unpaintedD
※1 Adapt to Mazda Radar Cruise Control (MRCC/SBS) .Except 360°View monitor model.


It has acquired a dynamic sport image. The DJ-05 styling kit comes with a half-type spoiler and front grill that can be mounted with LED daytime lamps. The side skirts set and rear roof spoiler, etc. support the kit. The center dual type premium tail muffler also further emphasizes the uplifting feeling which Demio gives you.

Styling Kit

previous arrow
next arrow
previous arrownext arrow

■DJ-05 Styling Kit for Demio(DJ 2WD)
DescriptionModelPart NumberPriceSpecificationCode
Front SpoilerAll ※1MDJ2100¥48,000Fiberglass,unpaintedD
LED Daytime LampAll ※2A002070¥20,0003-LED lamps with wire harnessD
Front Grille AllMDJ2500¥40,000Fiberglass,unpainted
For mazda genuine bumper
Side Skirt SetAllMDJ2300¥54,000Fiberglass,unpaintedD
Rear Under SpoilerAll ※4

For AutoExe
Muffler ※3 ※4



Fiberglass,unpainted Exclusive for MDJ8Y50/8Y60
Rear Roof SpoilerAllMDJ2600¥40,000Fiberglass,unpaintedD
※1 Except Mazda Radar Cruise Control (MRCC/SBS) model.
※2 Exclusive for AutoExe Front Spoiler(MDJ2100)
※3 When installing AutoExe Muffler,Rear Under Panel(Parts Number:MDJ2420)or Rear Under Spoiler(Parts Number:MDJ2410)are required.
※4 Except Mazda Rear parking sensor (MRCC/SBS) model.

Functional Parts

▶Suspension Parts

“A New Driving Sensation” – Suspension is the core of full running sports sensation.Our aim is handling at will, beyond the boundaries of mass-produced vehicles. For drivers who want to actively enjoy driving, not only the matter of simply stiff or soft feeling, but to be provided the best street driving specification which has refined the dynamic sensitivity performance such as the initial responsiveness at the time of steering and the transient characteristic of rolling.

Parts lineup

Low Down Spring
The roll is placed under control by the spring rate intensified within the range that has less impact on a ride quality, so that the vehicle height can be brought down by approx. 20 mm.  For the riding taste, the car stability is improved by bringing its center of gravity down, which provides a desired tendency to the “person who enjoys driving.”  Moreover, the clearance of tire house becomes reduced, which makes the whole car look low.  As a result, a dynamic feeling is provided to the styling.

■Sports Damper
The damping force of the rebound side in particular increased in comparison with the standard car controls the postural change.  The damping force of the bump side that causes the unpleasant jolt to worsen is almost as same as the standard car.  Further, the adopted dead low speed valve that moves smoothly when it starts to work controls the car posture properly from the extremely low-speed area.  As a result, the comfortable ride quality with less roughness and the sporty driving feeling go hand in hand.

■Street Sports SUS. Kit
The best street model anyone could ever think of for AutoExe. Based on dynamic sensitivity engineering, twin tube damper quickly initiates damping force at a very low speed region and controls the rolling response. Vehicle height is set for a 15 mm standard which realizes linear handling without impairing riding comfort.

■Adjustable Stabilizer Link
The length of the stabilizer link is designed with using the factory standard car as a guideline.  Due to this, when lowering the car height, at which time the angle of the lower arm changes, there is a tendency for arm angle of the link and stabilizer becomes more acute than the appropriate value, which spoils the true stabilizer effect.  The Adjustable Stabilizer Link is an item which allows the true stabilizer functionality to shine through by adjusting the link length when lowering down, so that the arm angle of the stabilizer is kept at the appropriate setting.

■Sports Stabilizer
The spring rate increased by the pipe diameter greater than that of the standard car reduces the roll at the comer.  It is not supposed to work as a spring when the right and the left tires go up and down simultaneously during straight-ahead driving, etc.  Therefore, worsening of ride quality is minimized.
Description ModelPart NumberPriceSpecificationCode
Low Down SpringDJ5FS



Ride-height -20mm D
Sports DamperAllMDJ7700¥60,000Replacement typeD
Street Sports SUS. KitAllMDJ7850¥158,000Ride-height adjustable
Adjustable Stabilizer LinkFrontAllMDE7605¥22,000Overall length adjustable Right and left setD
Sports StabilizerFrontAllMDJ7600¥23,000Solidφ22.0D

Body Parts

In order to increase the sense of unity between the driver and the car, tuning to train the body is fundamental. By decreasing the slight distortion of each part of the body generated by, for example, the force on the road surface while turning a corner, the motion of the initial operation of the suspension which was absorbed by the distortion is pulled out, enhancing handling with a sense of direct reaction from the moment you turn the steering wheel with no delay.

Parts lineup

Strut Tower Bar
It is a welded one-piece type with cylindrical rib that binds together the upper sections of the right and the left suspensions tightly with the strong steel pipe and plate.  It reduces the distortion of the body applied from the suspension to ensure the movement of the suspension.  As a result, it creates a zippy feeling of driving a car.  All the more because it is part of the basic item, we stick to the function-oriented stance.

■Center Floor Bar
Center Floor Bar is an auto body reinforcement part that enhances rigidity, by uniting the width of internal floor parts with high rigidity steel pipe. It is strengthened by the welded one piece structure, of the floor part and the center tunnel part. It improves steering performance by restraining distortion in the monocoque center parts where strut tower bar or floor cross bar do not work. Center Floor Bar can be applied to layout with the genuine floor mat, for rear legroom.

*Center Floor Bar can be applied to the genuine floor mat.
Photo Gallery

■Floor Cross Bar
It is a newly conceived reinforcement part that reinforces the floor by binding the right and the left sides of the rear floor with a steel pipe.  It produces the effect close to the tower bar without almost sacrificing the ease of use of the luggage room.  It concurrently uses the high-intensity bolt, etc. of the seat for installation, and won’t cause any annoying burden on the body, either.  We particularly recommend that it be installed together with the front strut tower bar.

■Lower Arm Bar(Front)
It uses the steel pipe to reinforce the right and the left bases of the lower part of the front suspension that greatly affect the steering.  Reducing the opening of the section where the suspension is attached to control the alignment change, it increases the secured sense of steering.

Tower Brace Set
It is an authentic part that has evolved the basic concept of strut tower bar more spatially while inheriting it.  Based on the oval shaft made of steel, it adopts the dedicated layout by vehicle type such as two way stress distribution structure and surface pressure distribution structure intended to avoid the stress concentration on the mount point.  As a result, it secures the unprecedented high rigidity as the bolt-on part.  Front and rear make a set.

■Member Brace Set
The whole open-structured floor such as the center tunnel and the lower part of fuel tank is thoroughly reinforced by the trussed frame that combines the tenacious steel pipe and gusset.  It reduces the vibration and the kink of the floor to allow proper function of the front and the rear suspensions.  When used in combination with the tower brace set, the upper/down two-stage high-rigidity body is completed.  Front and rear make a set.
Photo Gallery
Description ModelPart NumberPriceSpecificationCode
Strut Tower Bar FrontAllMDJ4000A¥24,000Steel 1-piece 2-point D
Center Floor BarAllMDJ4D00¥28,000Steel 1-piece 4-pointD

Floor Cross Bar RearAllMDJ4500


Steel 2-piece 3-pointD

Lower Arm BarFrontAllMDJ4B00


Steel 1-piece 2-pointD

Tower Brace SetAllMDJ4800¥58,000Steel 6-piece Front and Rear set D
Member Brace SetAllMDJ4700¥50,000Steel 3-piece Front and Rear set D

Intake & Exhaust Parts

For intake / exhaust tuning which has a direct impact on comfortable driving, improvement of peak power has no significance, but the reaction to instantly transmit the driver’s intention to the car.  Accelerator response is improved based on the air filter and the muffler with moderately reduced resistance. A discreet sports sound deepens communication between the driver and the car.

Parts lineup

■Air Filter Replacement
Used to replace the filter components but which allow utilization of the original air cleaner box. Dry nonwoven fabric that does not affect air flow sensors is used for the filter material. The specifications provide a good balance of ventilation performance and dust filtering. In addition, stainless mesh, which is not available with the original products, reduces any deformation of the filter medium at high engine speeds, while also easily and effectively improving accelerator response. Its disposable design also makes it easy to maintain.

■Sports Induction Box
Only the part of the genuine air cleaner cover that is of air intake resistance gets removed. Air intake efficiency is then improved by using the induction box with a genuine air cleaner element. The product sucks in fresh air and is comprised of an aluminum baffle plate that provides a thermal protection from the engine room and a funnel type FRP frame mounted in front of the filter. Efficiency can be further enhanced by combining it with an optional air cleaner. The sporty engine sound that results from removing the air cleaner cover also heightens its appeal.

■Ram Air Intake System
It is structured to take in more fresh air as the car runs more distance with the air intake directed forward the car.  Fresh air is not only efficiently taken in through the dedicated efficient filter, but also the insulation-efficiency and high-grade carbon is used in the main body.  Therefore, it produces the effect close to an incensement of engine displacement.  The sound of air taken in that you can hear even inside the car is comfortable, and your feelings of driving also run high.

■Fresh Air Guide
Directly catches the wind coming in from the front of the car, supporting improvement in suction efficiency. In mass-produced vehicles, there is no specific air intake path between front grill and air inlet, but the dedicated air duct connects them directly. This system minimizes the influence of waste heat flows out of the radiator, etc. and intakes fresh air into the air cleaner box.
Photo Gallery

■Intake Suction Kit
The flexible joint of mass produced intake hose, whose top priority is reliability, is dispensed, but the intake resistance is reduced by the design to maximize the effective flow area available. The materials of the hoses that have been specially designed for each engine are multi-layer polyester silicon which can provide excellent deformation control by intake negative pressure. As a result, acceleration response is improved. The engine compartment now comes accented in red.

■Premium Tail Muffler
Profound feeling with sophistication is the fascination of this series. An oval shaped tail end of 110X95 mm is exactly what is needed for a refined touch. The gentle sport sound that is controlled and muffled for driver and passengers, and improvement of accelerator response within a practical range, are coexistent with the large-capacity, straight-through silencer, in which a slightly smaller main pipe and inner structure are carefully tuned.

■Premium Tail Muffler (Center Dual)
Using stainless steel, 110 x 95 mm, oval shaped, two tail ends are installed at the center. The silencer is a straight structure item. By installing together with the dedicated rear under panel, the rear styling is completed with a sense of specialty.

※Single item cannot be installed. Photo Gallery

■Rear Under Panel
The dedicated rear under panel for simultaneous installation with a premium tail muffler. It supports the notch part of the outlet of the mass-produced muffler at the rear bumper, and it completes a rear view with a sense of unity with the muffler.
Photo Gallery

■Exhaust Finisher
Our exhaust finisher can be bolted on to the tail end of the genuine muffler but has a dedicated design for each model car. The oval shape with a thick and beautiful curve recasts the image of existing muffler cutters, realizing a sense of a perfect fit that general parts never attain. This exhaust finisher is perfect for any users wishing to add some spice to their machines without detracting from the specs of the genuine muffler. AutoExe logoed.
Photo Gallery

DescriptionModelPart NumberPriceSpecificationCode
Air Filter ReplacementAllMBM9A00¥6,500Dry type ReplacementD
Sports Induction BoxDiesel



Fiberglass filter frame+Aluminum air guideD
Sports Induction Box
with Filter



Fiberglass filter frame+Aluminum air guide+K&N air filterD
Ram Air Intake SystemDieselMDJ9590¥85,000Exclucive Wet type air filter+Carbon intake box E
Fresh Air GuideAll(Except 2020~models) MDJ9B00¥28,000Fiberglass 2-piece structureD
Intake Suction kitDiesel



Silicon layer structure hoseD
Premium Tail Muffler(Single)Diesel

Petrol 1.5L


Stainless steel Main pipeφ60.5 Tip95x80mmx2D
Premium Tail Muffler(Center Dual)Diesel(Except 2020~models) ※1

Petrol 1.3L ※1


Stainless steel Main pipeφ50.8 Tip110x95mmx2D
Rear Under PanelAll ※1MDJ2420¥28,000ABS,Painted(Dark grey)
Exclusive for MDJ8Y50/8Y60
Exhaust Finisher※2



Stainless steel Tipφ95x80D
※1 When installing AutoExe Muffler,Rear Under Panel(Parts Number:MDJ2420) or Rear Under Spoiler(Parts Number:MDJ2410)are required.
※2 For equiped standard muffler cutter models
※3 For non equiped standard muffler cutter models

Brake Parts

The cardinal point of the brake is to stop the car safely. The secondary expected function of the brake is easy control for the driver to freely reduce the speed of the car so as to enjoy driving as one wishes. As for sequential braking, it performs so as to synchronize the sensitivity of the driver using the brace for which delay reaction of braking can be solved by strengthening the rigidity of the mounting section for the pedal and the brake pads with a small change in the coefficient of function.

Parts lineup

■Street Sports Brake Pad
“Deceleration of at will”, it is our goal. Not just for the performance in stopping, the design focuses on the stable effectiveness at the time of continuous braking, meticulous load shifting while cornering, giving very flexible control of the vehicle speed. On the assumption of driving on the road, the coefficient of friction (μ) is constantly changing depending on the conditions such as breaking actions, speed of the vehicle, and temperature, etc. The variation of such changes and how it changes became our interests. Sport-oriented drivers’ sweetheart, “transient property of μ”, generates spice which synchronizes the sensibilities.

■Street Brake Rotor
Street brake Rotor has the same one piece structure as the mass produced rotors.
Content of carbon and silicon have been changed to strengthen the component.
Moreover, metallic bond formation is stabilized by a thorough heat treatment process, which is abbreviated in mass produced rotors. This results in restraining heat distortion, and improves fade resistance. Other remarkable features are as follows: function to let out fade gas generated from heated brake pad, or cleaning slit that planes the surface of carbonized brake pad and enhances brake operation.

■Brake Pedal Brace
Brake Pedal Brace has been developed with the same concept as the Mastervac Brace. It is a component of the FF/4WD models that have no space for bracing in the engine compartment. It reinforces the bracket of the brake pedal parts from all angles and maintains its rigidity, where slight distortion occurs in braking operations. This improves the time required between pedaling and brake operating, contributing to the feel of brake operating instantly.
Description ModelPart NumberPriceSpecification Code
Street Sports Brake PadFrontAll MDJ5A10¥15,000Asbestos-freeD
Street Brake RotorFrontExcept 1.3L Petrol

1.3L Petrol


With cleaning slit,Replacement type D
Brake Pedal BraceFrontAllMDJ4950¥18,000Steel 5-pieceD

Drivetrain Parts

Pull the potential of the engine completely out and convert it into traction on the road surface. A sports clutch set and a flywheel to support brisk gear change. While increasing the feeling of being directly connected with the car, Limited Slip Diff, for example, the driver positively enjoys the change of the attitude of the car in turning a corner, and the transient characteristic, where abrupt movements are eliminated as much as possible, are built in.

Parts lineup

■Turbo Pipe
Aluminum elbow pipe with an optimized pipe layout and with utmost mirror surface of the inner wall, and polyester silicon with high deformation control are compounded to reduce the expansion of the hose by compression and the resistance of the air flow path. Boost pressure is increased and the turbo lag is reduced. Car responds better as soon as the accelerator is stepped on.

Sports Clutch Line
The stainless steel mesh PTFE (Teflon) clutch line creates extremely small expansion generated by oil pressure, and very littledegradation due to lapse of time compared to rubber clutch line which is used in mass-produced vehicles. The feeling of the clutch is more direct and lasts for a long time. In addition, a PVC coating is applied to protect the hose.

DescriptionModelPart NumberPriceSpecificationCode
Turbo PipeDieselMDJ3960¥42,000Aluminum pipe+Silicon layer structure hoseD
Sports Clutch LineM/TMDJ6500¥10,000Stainless steel PTFED

Utlity Parts

The surface texture and the usability have been given great attention in order to enjoy pleasant, everyday driving in addition to well behaved running. Enjoy the utility items, namely side visor with ventilation system which improves the style with sporty aeroform and the bonnet damper supporting opening / closing of the bonnet, equipped with superb functionality which is not found in mass-produced cars.

Parts lineup

■Oil Filler Cap
The mass produced, resin oil filler cap is replaced with machined 52S aluminum, adding a touch of craftsmanship. Bright red, anodized processing accentuates a glamorous mechanical flavor to the engine compartment. Laser engraved AutoExe logo expresses a sophisticated look. Two lineups of one-touch type and screw type can handle a wide range of old and new Mazda cars.

Oil Level Gauge Grip
The resin grip of mass produced oil level gauges is replaced with an aluminum grip. Laser engraved AutoExe logo with red anodic oxydation coating offers a stylish look to the engine compartment. DIY installation is available by using the exclusive tools which come with the kit. Total coordination by installing the elaborately designed oil filler cap is recommended.

Battery Clamp
Now the engine compartment comes in accented red, which supplements a playful taste. Made of one piece steel with the design of an AutoExe strut bar in mind. Everything has been faithfully reproduced, even the logo plate of the bar.

■Fuel Cap Cover
Cumbersome self refueling will turn out to be a fun time to interact with your car. ABS cover which is installed by covering mass-produced fuel caps. The design of the cap bolt arranged with a vivid red color gives a gorgeous impression to the fuel filler opening. Engraved with AutoExe logo. The fuel cap cover is extensively compatible with the current Mazda cars. Using double-sided tape  A caution label indicating the specified fuel for the car is attached.

■Aero Sports Wiper Blade
The wiper blade has the Aero shape. The Aero form extends to the arm joint section, because of the large deflector which is equipped with fins. The wind pressure generated while driving is actively received in the blade and suppress lifting of the wiper. The blade rubber evenly adheres to the glass surface, improving visibility during high speed driving in the rain. Equipped with stainless steel AutoExe ornaments.

■Bonnet Damper
High pressure gas damper assist makes opening and closing the bonnet even easier and smoother. The conventional lock stay is also no longer required, thus significantly improving the maintainability of the engine room. Special mount brackets for minimizing the load on the connecting parts, bonnet, and frame enable simple bolt-on installation with no holes being necessary.

■Sports Side Visor
Effective ventilation system High performance side visor with ventilation function, in addition to the effective rain proof and shade. When opening windows, indoor air is pushed out using the negative pressure generated while driving. It’s also very effective to prevent rain from coming in. The rubber blade, equipped with a visor, controls a whirlpool of air, which is discharged. It prevents backward flow into the inside of the car. Aeroform in pursuit of higher performance also adds a dressy appearance to the car. Smoke type/acrylic resin.

■Wheel Nut Set
It is a fashionable small-diameter wheel nut that places the aluminum end cap with a logo of AutoExe on the top.  The design of oddly shaped heptagon intended to use the dedicated adaptor wrench for attachment is adopted to allow the combined ue that protects the wheel from theft, too.  The high-strength chrome-vanadium steel that resists loosening under high temperature is adopted as a raw material so that the durability and the reduced diameter can go hand in hand
M12XP1.5 L:32mm.
DescriptionModelPart NumberPriceSpecificationCode
Oil Filler CapAllA1400-03¥5,800One touch type Anodized aluminumD
Oil Level Gauge GripAllA1450-03¥5,800Anodized aluminumD
Battery ClampAllA1700¥6,800Steel 1-piece D
Fuel Cap CoverAllA1600-03¥4,800ABS,Painted(Red)D
Aero Sports Wiper BladeAllMDJ0250¥8,800With built-in wind deflector
Right and left set
Bonnet DamperAllMDJ2960¥20,000High pressure gas dampers
+mount brackets
Sports Side VisorAllMDJ0400¥15,000Acrylic resin With ventilated 4pcsD
Wheel Nut SetAllA00100B¥12,800Chrome-vanadium steel
+Aluminum end cap
Helical Short AntennaShort Antenna modelA1460¥3,800L=80mm Screw pitch:M5 with Mount colorE

Interior Parts

In order to clearly transmit the intention of the driver to the car, the texture and the functionality of the cockpit are meticulously designed. For the interior, we have a steering wheel with a built-in airbag and a casually pleasing sport sensibility; and we have focused on a shift knob, the operation of which provides a tangible feeling. Please enjoy exchanging intimate dialogue with your car.

Parts lineup

Sports Steering Wheel
It has a sporty flat bottom shape. Pursuit of details created the steering wheel with an oval shaped section which provides easy handling, as well as the thumb grip which controls slipping. The diameter of the wheel is 370 mm* which is the same as the standard for mass produced cars, as a result of valuing operability and visibility.

■Carbon Paddle Shift Lever
High-grade real carbon material to cover the mass-produced steering shift switch. Improved operability from moderate upsizing. The lever provides confidence in sports driving, and tailors the cockpit for a sporty look. Engraved with AutoExe logo. Double-sided tape type. Four pieces assembled.
・Supports standard equipment / genuine optional steering shift switch.
・Overall length 100 mm (mass production ratio, upper + 25 mm and lower + 10 mm extension)

■Shift Knob (Leather/Ball Shape)  Designed for A/T models.
A round shaped knob designed exclusively for the latest Mazda AT models with straight type gear. It is a press-to-use knob and designed with care to be comfortable even when unlocking the shift lock. Genuine leather/red stitches. AutoExe logo marked.

■Shift Knob (Leather/Ball Shape)  Designed for M/T models.
Made of genuine leather; 51 mm in diameter with operability in mind. Shift knob easily fits in your palm, and you can hold it both up and sideways. Height is easily adjustable according to the size of the driver and the driver’s taste. Choice of red stitch and black stitch is available. AutoExe logo is engraved on the top.

■Shift Knob (Leather)  Designed for M/T models.
A size with a small diameter of 42 mm. Shift knob which easily fits in your palm, and  you can hold it both up and sideways. Height is easily adjustable according to the size of the driver and the driver’s taste. Choice of red stitch and black stitch is available. AutoExe logo is engraved on the top.
Description ModelPart NumberPriceSpecificationCode
Sports Steering Wheel(Leather)Red stitch

Red stitch



D-shape φ370mm Real Leather D
Carbon Paddle Shift Lever Steering Shift Switch ModelA1382-20¥14,800Carbon 4-pieceD
Shift Knob
(Leather/Ball shape)
Red stitch

Red stitch



Genuine leather Push type

Genuine leather Screw pitch:M10X1.25
Shift Knob(Leather)Red stitch

Black stitch



Genuine leather Screw pitch:M10X1.25D